ZGEMMA H9S DVB-S2X Multistream 4K UHD Enigma2 4core ARM

hi hisakatano

Is powervu still working?? if so how have you configured dvbpi and stream relay?

Hi Hisakatano

Thanks show me how DVB-API and strem relay configured

below is stream relay

Mode (disable to use direct dvbapi decryption)

Process EMM from stream

Source Stream Host:
Source Stream Port:
Source Stream User:
Source Stream Password:
Relay Port:
ECM fix delay:

Hi hisakatano

Thanks for your guidance ...its working now. But which softcam key are you using???

Iam in South Africa I need sony as well. Is possible to have your autoroll softcam.key?

68.5 E sony 3900 H 22222

66E sony 3800 H 30000

In South Africa we do not have 105.5 I get LePLEX HD through satellite streaming

Thanks hisakatano

let me try and i will update you many thanks once again. I had stopped using Zgemma because oscams stopped working for a long time and i had forgetten how to use oscams. I was using plug and play receivers for end users. I like sony channels very much pix , sony six and espn are my favourite channels

Hi hisakatano

Thanks for the softcam, but sony 68.5e not working sony 66e i have no signal dish needs alignment

afn working fine....

thanks hisakatano for al, but not work powervu in my h9s, iam in northamerica, you config working very fine in a dm900 clone, but in my zgemma h9s not work.

Hi gatonico

try with openatv 6.2 or openatv 6.3 images, it should work as well

Hi all,,

I want to ask if powervu DES can open on zgemma H9S ??? Cartoon network channels on the asiasat7 satellite and Setanta HD channel on the Measat satellite are dark even though the oscam and key function normally ...

Think about the solution ... Thank you

Hi all, Powervu direct don(t work with Zgemma series, you install your channels with manual method fromthis page and it's nice...

Pour optimiser les performances, le paramètre "Inclure l'ECM dans les flux http" doit être activé. Si votre image le supporte (openpli, openatv), vous pouvez le trouver ici: OpenWebif -> Paramètres -> Personnaliser

- Si le paramètre n'est pas disponible, vous devrez peut-être régler le paramètre "Délai de réparation ECM" dans oscam webif (Config -> Stream Relay). Augmentez / diminuez jusqu'à ce qu'il n'y ait plus de bégaiement.

- Lors de l'utilisation de périphériques VU +, veillez à utiliser les derniers pilotes (juin 2015) si vous rencontrez des problèmes.

Channel Config:

1. Allez sur OpenWebif et cliquez sur le bouton "Stream" du canal que vous souhaitez ajouter.

2. Téléchargez et enregistrez le fichier .m3u.

3. Ouvrez le fichier .m3u avec un éditeur de texte et récupérez le lien de flux. Cela ressemble à ceci:

http: // stb: 8001/1: 0: 19: 1234: 3EF: 1: C00000: 0: 0: 0:

4. Remplacez le port (8001) par le port de relais (valeur par défaut: 17999).

http: // stb: 17999/1: 0: 19: 1234: 3EF: 1: C00000: 0: 0: 0:

5. Ajoutez le nouveau lien de flux à votre liste de chaînes (par exemple avec DreamBoxEdit).

Remarque:

- Lors de l’utilisation de DreamBoxEdit:

- A. Allez dans la liste du volet central "Détails du bouquet utilisateur de télévision".

- B. Faites un clic droit sur une chaîne, sélectionnez "IPTV et autres services de diffusion en continu", sélectionnez "Ajouter".

- C. Sélectionnez "DVB / TS".

- D. Choisissez un nom et utilisez le nouveau lien de flux en tant qu'URL.

- E. Utilisez le "Service ID" du canal d'origine. Vous pouvez le trouver dans la liste de gauche ("Services").

Mais je ne l'ai pas encore testé pour deux raisons:

1. En ce moment loin de mon système satellite.

2. J'ai le Dreambox DM800 HD PVR qui a un processeur plus lent (333 MHz).

Un séjour sans faille

Guys,

it is about few months I have bought a H9S and I want to share with you all my opinion and issues I had

1) Why go cheap on the display? It was very handy to have a small display like in my previous H2S

2) I am living in Belgium and I am mostly pointing my motor Sat dish to 13E or 19E, I have being trying different images (openATV, OpenPLI, ..) with all of them I use CCCam and I have the same issue when zapping I have got 1 or 2 seconds of slow motion, anyone had the same? Any tips? Thanks in advance

Stefano

Quote from ak2013

Hi gatonico

try with openatv 6.2 or openatv 6.3 images, it should work as well

thanks i will probe with openatv 6.2 because with 6.3 not work for me the emu work but not show image

Hi, at Stefano, it's an problem with this product, it's an china not too expensive my friend, but nice ...