Switched to your build of OSCam-11759-801 this morning and Sky De does not work
New config from here:
( RE: Samur's OSCam - Request for compilation, questions and help !!! )
;
Switched to your build of OSCam-11759-801 this morning and Sky De does not work
New config from here:
( RE: Samur's OSCam - Request for compilation, questions and help !!! )
;
Samur, prosím, môžete poslať test na kôš 0624 aj pre mips box. Ďakujem
samur please can you send the test to basket 0624 for the mips box as well. well thank you
see, if decoding don't takes 10 minutes to start ...
On both DM TWO and Octagon, the image does not start immediately. I didn't want to wait long to see if it would start at all. I waited more than 5 minutes and nothing.
Samur test version does not work waiting 15 minutes. Previously version 11759-801 works without problems loading 10 seconds on oscam restart.
The test version does not work on a raspberry rpi4. I waited 5 minutes and no picture. The previous version works perfectly
Is it possible to modify oscam to accept the Plustelka card (0668)?
PLUSTELKA | Televízia, s ktorou si budete rozumieť
(3) ATR : 3B 9F 21 0E 49 52 44 45 54 4F 20 41 43 53 20 56 36 2E 30 9E
(3) Reset Baudrate = 9600 Baud
(3) Irdeto 2 V6.0 ACS 0.06
(3) Serial (UA) 4276xxxxxx (8F1xxx)
(3) Base 12
(3) Provider00 03 FA xx date 04.04.2024
(3) Provider01 FF FF FF date 04.04.2024
(3) Provider02 FF FF FF date 04.04.2024
(3) Provider03 FF FF FF date 04.04.2024
(3) CaID1 0667
(3) CaID2 0668
(3) CaID3 0601
(3) CaID4 0602
(3) Camkey 112233448F1xxx12
(3) Camkey OK - 312 ms
(3) Working Baudrate = 7258 Baud
latest oscam 11759-emu good working for my vusolo2 hd box thank you for help
Display More(3) ATR : 3B 9F 21 0E 49 52 44 45 54 4F 20 41 43 53 20 56 36 2E 30 9E
(3) Reset Baudrate = 9600 Baud
(3) Irdeto 2 V6.0 ACS 0.06
(3) Serial (UA) 4276xxxxxx (8F1xxx)
(3) Base 12
(3) Provider00 03 FA xx date 04.04.2024
(3) Provider01 FF FF FF date 04.04.2024
(3) Provider02 FF FF FF date 04.04.2024
(3) Provider03 FF FF FF date 04.04.2024
(3) CaID1 0667
(3) CaID2 0668
(3) CaID3 0601
(3) CaID4 0602
(3) Camkey 112233448F1xxx12
(3) Camkey OK - 312 ms
(3) Working Baudrate = 7258 Baud
i need a debug 4 log from initial till first CW .
and provide the debug 4 log in '.txt' Format file
##
if i understand the card is not an RTVS Card ...???
;
if i understand the card is not an RTVS Card ...???
Plustelka is a paid service of Towercom for DVB-T2.
It has cards with the same CAID as RTVS for SAT, but they are not interchangeable.You cannot use the Plustelka card to watch the RTVS offer via SAT, and vice versa, you cannot use the RTVS card to watch the Plustelka offer via DVB-T2.
I hope I wrote it well and clearly.
Display More(3) ATR : 3B 9F 21 0E 49 52 44 45 54 4F 20 41 43 53 20 56 36 2E 30 9E
(3) Reset Baudrate = 9600 Baud
(3) Irdeto 2 V6.0 ACS 0.06
(3) Serial (UA) 4276xxxxxx (8F1xxx)
(3) Base 12
(3) Provider00 03 FA xx date 04.04.2024
(3) Provider01 FF FF FF date 04.04.2024
(3) Provider02 FF FF FF date 04.04.2024
(3) Provider03 FF FF FF date 04.04.2024
(3) CaID1 0667
(3) CaID2 0668
(3) CaID3 0601
(3) CaID4 0602
(3) Camkey 112233448F1xxx12
(3) Camkey OK - 312 ms
(3) Working Baudrate = 7258 Baud
capture_003_04042024_212240.png
(ATR: CE FC FE 02 3C C0 8C 8C 0E B0 32 0E B2 7E 0E BC CE CE 72 3C B2 BC)
Could there be a problem with the card reader?
So what is the correct ATR value?
Hi samur,
On my old DM 7020HD V1, Openatv 7.2, SkyDe (icam) with such config:
[streamrelay]
stream_source_auth_user = local
stream_ecm_delay = 5
stream_relay_ctab = 098D,0960,0961,0963
is Ok with OSCam_11734-r799 but not with OSCam_11759-r801 (your last mipsel).
I try also with :
[streamrelay]stream_relay_enabled = 1
stream_relay_buffer_opt = 0
stream_relay_buffer_time = 600
stream_relay_ctab = 09C4,098C,098D
stream_ecm_delay = 0
but no way with both 734 and 759
Please any help?
I tested both aarch64 and ARM and now they are OK.
That's why it took me a while, because I was testing not only the start-up of the card after restarting the box. But even separately, especially pulling out the card while running, I waited a while and inserted the card into the slot again. Everything starts well and quickly.
Good work bro.
I tested both aarch64 and ARM and now they are OK.
Just, a clarification:
With my binaries you need just to test one Architecture (arm, aarch64, ...etc)
and if it's OK then all others are OK.
;
Don’t have an account yet? Register yourself now and be a part of our community!