Posts by habib2535

I am switching from NN2 to OpenPli 7.2... some people managed to make the usb stick work with OpenPLI

I am switching from NN2 to OpenPli 7.2... some people managed to make the usb stick work with OpenPLI… i will test and report

I am struggling too…. look at my parallele post with same title… have you tried the driver .ipk suggested by MASTER G ?

try command "$ usb-devices" instead and look at the Manufacturer for each usb port shown (I have seven ports shown on my box)… the TL-WN821N appears as follows

T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0

D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1

P: Vendor=2357 ProdID=0107 Rev=02.00

S: Manufacturer=Realtek

S: Product=802.11n NIC

S: SerialNumber=00e04c000001

C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA

I: If#= 0 Alt= 0 #EPs= 5 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

thanks for the help… Another hint

when i type # modinfo rtl8192*

NN2 returns this

modinfo: ERROR: Module rtl8192eu-linux-driver-master not found

(actually i did a previous attempt following tutorials from the manufacturer to compile the driver on linux but i stopped the sequence as the tutorials were not meant to apply to NN2 environment…. i have been asked to issue a dkms command ! anyway… )

Thanks…. The installation went well but my stick is still not recognized

to the command # usb-devices i can read this is the usb N°5

T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0

D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1

P: Vendor=2357 ProdID=0107 Rev=02.00

S: Manufacturer=Realtek

S: Product=802.11n NIC

S: SerialNumber=00e04c000001

C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=500mA

I: If#= 0 Alt= 0 #EPs= 5 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

yet my usb is a TP-Link TL-821N and in TP-Link website the driver pack indicates clearly that the chipset is rtl8192eu thus my request…

but as you can see there is still no driver attached to the stick ! : Driver=(none)

is there a way of forcing NN2 to attach the installed driver to the usb device ? or any ther command that establish the association ?

______________________________________

and btw if i issue the command # apt-get install kernel-module-rtl8192* …. i read this

kernel-module-rtl8192c-common is already the newest version.

kernel-module-rtl8192ce is already the newest version.

kernel-module-rtl8192cu is already the newest version.

0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.

but the driver rtl8192eu is not listed after the above install

yes please… i am using NewNigma2

it is what i thought… doesn't appear in the manual install if placed in /tmp… is there any firmware-rtl8192eu_1.0-r0_all.deb ?

thanks you master G... can an .ipk be downloaded on a DM900/NN2 ? thought it should be an .deb ? let me try anyway and i will report

emosim : you are right ! vhannibal setting is not adapted to my device - a MANUAL full satellite re-scan solved my problem. Nothing to do with the dish or LNB or any other harware issue. i spend hours adjusting my dish ... all useless

Thanks for the hint ...

I will keep working on adjusting my dish because my receiver cannot lock the weak transponders anyway so i cannot launch a manual scan

my box is flashed with the latest vhannibal setting (June 27 2018). May i assume that satellites.xml is properly setup ?

Ok i tried some dish adjustments but no change... I will try some more advanced corrections of my motorised dish and see

can i precise that this failure happens only on DBS-V2 transponders, not on DVB-S's .... Does that make any difference ? or is it a simple coindidence ?

Thanks Emo... I have loaded the latest vhannibal setting but i will try to refocus my dish indeed and will report

Hello

I have an old DM8000HD (7 years +) running under Oscam with last setting vhannibal.

I have observed since a couple of months that i cannot receive anymore some Astra FTA channels such as LCI, TV5 Monde ... all transmitted in DVB-S2 mode . However, i can receive very well other FTAs channels CNN Euronews etc... when transmitted in DVB-S

when i observe the signal of LCI transponder for instance (12207 V 29700) the SNR level is lower than 30% and my DM couldn't lock the signal !

Now i bought yesterday a cheap other receiver (SaghemCom Canal Ready) and i can receive LCI and all other channels with no problem and with same dish/lnb/cable installatio (the signal strength is shown with a very good quality)

I do not understand this change of behaviour that apparently happens on DVB-S2 transmissions only. I tested this on both Tuners of my DM8000HD ... same problem

Is it a tuner issue ? Anyone has an opinion ?

On my PC i tried two VLC version 0.8.1 and 0.8.6 that i launched with " --intf wxwin --extraintf=http" argument, after having declared 8080 as streaming port
On my DM8000, running Dream-Elite image of 19/03/2016, I downloaded VLC-Plugin and created a link to my local LAN PC server on port 8080

There is no way to make VLC-plugin work ! when i click on the created link to the server i have an error message like " ... cannot load the file list, HTTP 501 ERROR : NOT IMPLEMENTED "
Any hint on where i should go from here ?

For reference,
- i can connect to may PC server from my Dreambox through other means (media player, etc...)
- i have already succeeded in the past to make VLC plugin work but under other images...

Gents - just subscribed 2 days ago for Canalsat for one year and have been told afterwards that Oscam/DM8000 cannot read the card ! I have it inserted on Dev/sci0 and indeed got it activated OK 03-Aug-2016 but... BLACK SCREEN !

1) Is there a config to read the card ? Here is what i have for now and that allowed the activation
[reader]
label = Canalsat
protocol = internal
device = /dev/sci0
services = Canasal
caid = 0500
ecmwhitelist = 500
detect = cd
mhz = 500
cardmhz = 357
ident = 0500:032830
group = 1
emmcache = 1,3,15,0
auprovid = 032830

2) what other ways i have to read the card on a DM8000 (any softcam ? hardcam ? )

ouf... solved my problem in another forum ! stupid reasons : the picon folder need to me named picon_220x132

I just tried "Picon" (only first letter Upper case)... no change

the error message i have has this shape
find : proc/577/task/838/fd/139 : No such file or Directory

I have 5 or 6 of these and then the plugin freezes...

I can't believe this is linked to whether you use a USB stick, hard disk or flash memory but i feel that if i can make this plugin work i will also come back to my manual stuff and it would work as well !