Thank you Master G & Bobby-
Posts by rasp
-
-
I have unzipped them and transferred them to usr/share .
I usually change the bootlogo from plugins/downloads/ bootlogo.
Or do i ftp the full file not unzipped
-
Where do do install these to.
Can you install the two or one at a time.
Thanks
-
Ditched the rg59 cable and bought 20mtr of RG6 made one off snug fit on the cable.
Not going to use compression fittings.
The only problem i have got is the lounge has been decorated paper and painted and er indoors has said you are not making any mess trying to get the cable through the wall.
-
I have been given 20mtrs of rg59 twin cable.
I have two type of f connector rg6 and sky.
The RG6 i had to cut a load of outer sheath and pull braid back just for it to grip and for the sky i had to force it on twisting the cable for the extension i used to test
Are there any connectors for the rg59
-
It's the cable took one out of sky dish put in line connector and a piece up to motor and moved it west.
The original cable is wf 100 and the extension was rg59 cable .
So the problem is cable on the motor or going into the box
-
My motor has stooped working no led flashing and i cant move east or west.
Checked cable connections all seemed fine.
Happened after i changed from Triax 110d to 88cm dish.
Set the dish to zero moved ok but from then on no go no led flashing.
I am shortly going to run a cable form the sky dish to the triax to see if its the cable.
As i have put the cables from the sky box in to the vu solo4k and can get 28.2 all working fine.
If it's the motor i will try the technomate TM 2600 as i have only had the motor about 18 months
-
Addons working OK now.
Ts media icons OK as well .
Still get the occasional crash but just learning to use blackhole can put up with that.
Oscam works OK
-
When i go the linux support and blackhole addons says no internet connection and i know it is ok
I reflashed with this image was using vix image it's good just getting my head around it.
On ts media on every section if i move over a icon like addons the box is half way to the rght of the icon
-
Nice Skin but i have gone back to vix skin.
On the channel i am one i like to see the signal level and which line is working in oscam
-
Somebody else is at skin and image:
http://www.ebay.co.uk/itm/Enig…93db55:g:uHsAAOSwAvJXATfD -
Just been on ebay nothing happened yet
-
Just reported him Wanker
-
Loaded latest ipk nothing working
- - - Updated - - -
It's working my fault loaded wrong file
-
where in the mg_cfg did you change mips to arm ?
05 openbox
# 06 dreambox/arm#I loaded the files all again g had been changed before after i altered the above it started to work.
Upddate.
It also stops with me say i switch channel i have to restart it
-
I have got it working.
Changed G TO (33)
And in in the mfg.cfg changed from mips to arm not sure which one got it working
-
Loaded OK thanks Master G:.
Put 2 clines into ccamd list and nothing happens.
The same 2 lines are put into CCcam to oscam converter and transferred as oscam server file work ok.
So i know it not the lines what am i doing wrong.
The files i have are:
ccamd.
mg.cfg
newcamd
softcam
-
Ftp it box and installed through extensions does not not show anywhere
Vix image
-
It will be there sometime Friday and they will try three times before getting in touch with me i will leave till tomorrow afternoon before sending and you get it Friday afternoon or Saturday.
It's well packaged so it will take a good half hour to unpack it
- - - Updated - - -
Sent midday today let me know when you get it
- - - Updated - - -
Forgot the basic setup guide but i have uploaded the user manual for you.
Let me know if you want guide but the manual has everything.
SOLO2 User Manual_English.pdf -
Will be on its way tomorrow A.M. will have to be signed for will there be somebody there to sign for it