Posts by MotoPt

  • New out of box bad dm900

    Hi, I try... only apear red mark exclamation, no recovery mode, no ip adress, no telnet...nothing work, only get log from service port:


    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2017.10.07 16:16:06 =~=~=~=~=~=~=~=~=~=~=~=

    CPU 01

    Dreambox DM900


    AVS init...

    AVS init OK

    AVS load:select_image: addr_offset: 00051000 part_offset: 00000000 bootStatus: 2a002b00

    AVS load_code offset =00051000

    LOADED

    AVS: overtemp mon ON


    single board

    select_image: addr_offset: 00055000 part_offset: 00000000 bootStatus: 3d2b2500

    MEMSYS-STD

    SHMOO 02010000 BLD:11138M HW:hpf0_b1p6 V:2.1.0.0

    MCB: FLEX

    AVS start:status=000000ff

    STB: Current voltage=0000038e(910)

    temperature=0000e621(58913)

    PV=0000034d(845)

    MV=00000392(914)

    AVS FW rev=30333278 [0.3.2.x]

    OK

    DDR0: !@ ffe0e780 <= ffe0df10 MEMSYS-0 @ f1100000 OK

    DDR1: =@ ffe0e780 <= ffe0df10 MEMSYS-1 @ f1180000 OK

    Sdram Scramble OTP = 0x00000001

    Sdram Scramble OK

    select_image: addr_offset: 00020000 part_offset: 00000000 bootStatus: 1b25252b

    BFW load mode OTP = 0x0000000f

    bfw_hash_locked = 0x00000000

    BFW key3 OK, BFW load OK

    BFW v2.1.0

    COPY CODE... DONE

    MICH: disable success

    SSBL

    PINMUX

    CACHE FLUSH OK

    MMU ON

    CACHE FLUSH OK

    _fbss 07080cd0

    _ebss 0713dd70

    _end 0713dd90

    HEAP @ 07200000

    STACK @ 09300000

    ARCH: CONFIG OK

    CLR BSS 07080cd0 to 0713dd70 OK

    CLR SRAM OK

    CACHE FLUSH OK

    CPU CLKSET OK

    GO!


    [33;1m ,/ [0m

    [33;1m ,'/___,[0m BOLT v1.18 v1.18 LOCAL BUILD

    [33;1m.'__ ,' [0m (2017-03-07 20:27:59 cynric@cynric-VirtualBox)

    [33;1m /,' [0m Copyright (C) 2017 Broadcom

    [33;1m /' [0m

    [0m

    Board: BCM97252SSFF

    SYS_CTRL: product=72521, family=7439b1, strap=000000b2,

    otp @ 0xf0404030 = 0x822000e0: en_cr(0x00000060) en_testport(0x00000080) macrovision_disable(0x02000000) moca_disable(0x80000000) rv9_disable(0x00200000)

    otp @ 0xf0404034 = 0x00000021: moca2_disable(0x00000001) rfm_disable(0x00000020)

    CPU: 2x B15 [420f00f3] 1719 MHz

    SCB: 432 MHz

    DDR0 @ 1067MHz, DDR1 @ 1067MHz

    RESET CAUSE: 0x000001 power_on (1 of 23 possible causes)

    CS0: SFDP SPI, 32MB, 64kB blocks, 64kB erase block, 256B pages

    [31;1mCS1: NAND: unrecognized ID: 0x20ffff 0xffffffff[0m

    RTS0: 0x1101004, 256 clients, ok

    RTS1: 0x1181004, 256 clients, ok

    BOX MODE: 5

    card if inited

    set pwm to 0/255

    disp id 0000

    load image

    AVS: park check

    AVS: temperature monitoring enabled

    AVS: STB: V=0.910V, T=+60.861C, PV=0.845V, MV=0.914V, FW=30333278 [0.3.2.x]

    USB otp=00000040

    USB @ 0xf0470200: IPP is active low, IOC is negative polarity

    init fp

    found card in unknown state

    cannot read T1 header

    error in receive

    error during t1 transfer

    cannot read fabca-cert

    retrying.. card if inited

    found card in unknown state

    cannot read T1 header

    error in receive

    error during t1 transfer

    cannot read fabca-cert

    retrying.. card if inited

    found card in unknown state

    cannot read T1 header

    error in receive

    error during t1 transfer

    cannot read fabca-cert

    retrying.. card if inited

    found card in unknown state

    cannot read T1 header

    error in receive

    error during t1 transfer

    cannot read fabca-cert

    retrying.. card if inited

    found card in unknown state

    cannot read T1 header

    error in receive

    error during t1 transfer

    cannot read fabca-cert

    retrying.. card if inited

    set pwm to 200/255

    TPM error. Please contact Dreambox support