Posts by WaMan

  • Lnb settings

    My Gtcombo Receiver was working on GTMedia software before I started

    I flashed Mars on my GTCombo , the lnb settings don't work, just like the antenna is not hooked up.

    I tried different Mars software, nothing worked.

    I flashed the Combo back to gtmedia with burning software, I found on this Forum, seemed successful, thanks for the help.


    I still dont have any lnb settings that work Cband or KU.

    My other receivers seem fine, I tried one on same cable no problems, I have good signal and quality on other receiver.

    I have factory reset , nothing is working.

    Any Ideas to try, is welcome

  • HOW TO: USB Burning tool Recovery of GT Media Combo 4k

    I found it on page one, just overlooked it Thanks

  • HOW TO: USB Burning tool Recovery of GT Media Combo 4k

    Would someone share a link to download Burning tool and a image firmware

    Gtmedia site removed all there download

    I have a Male USB to USB cable

    Or uplad it for few hours or so for me to download and try and recover mt Gtcombo

    YOU NEED THESE:

    1.Male to Male USB data cable


    2. Some .img firmware (attached)

    3. USB burning tool Software (attached)

  • Telnet

    I'm still learning and I have been googling to find a answer

    anyway, I want the command, to telnet with putty in to my engima2 receiver and see my latest scanned transponders

    thanks for any help

  • Biss with oscam

    I have got comfortable with Biss

    I now want to tackle Powervu


    which image openatv or open8eight



    The reader file, that I see all over the forums, does it go in the softcam server file

    or a how to config file


    I saw the video on stream relay, how to add channel, I think, I can do that

  • Biss with oscam

    I can go to my web interface via web browser, no problem using receiver IP

    I don't have to add the :8081 or :8888 to bring it up. I don't see anything that says files

    I have settings/softcam settings

    I have two checkboxes

    show oscam extensions

    show ccam extensions

    nothing else, I can find

    I have my softcam file in etc/tuxbox/config/softcam.key

    it is in with the other oscam folders

    there is no folders in usr/keys

  • Biss with oscam

    I'm going to try again tonight, any help would be appreciated,

    I tried ncam and oscam , still haven't been able to open biss channel

    I know the key is good, it works on my technomate just fine

    I currently have openatv 6.1 with oscam-emu

    At this point, I just want to see it open up:D

    I've tried softcam.key and constant.cw, I put files in user/key and etc/tuxbox/config,oscam

    I tried all kind of configurations with pids, hex and decimal

    I tried keys on one line

    two lines with keys

    the key twice on one line

    I'm not sure about permission thing either 644,755,777 if it is even

    necessary

    I know , I missing something here , easy

  • Biss with oscam

    Thanks, for the reply


    I went with the oscam-emu 11226 openatv mips 32 ipk cam

    I'm have ATV 6.1

    I loaded the ipk file usb style


    I put the softcam file in the usr/keys folder along side Oscam files

    I didn't have any luck opening the biss channel

    I edited the softcam contents, trying some things

    I only have the one key in place.

    The softcam file looks like this

    F sid-ecm, key# Key channel ID


    ##BISS####################################

    F 000E2600 00 ################ ; channel


    F 000E2600 01 ################ ; channel


    I didn't have any luck

  • Biss with oscam

    I'm trying to learn how to open a biss channel using oscam

    I have oscam installed, I can see it on receiver and filezilla

    I need to know if I use a softcam.key file or constant .cw file or both (Is there a certain softcam file You use)

    I don't want a big file of keys, just a few when needed, I can add to

    I need to know what file they go in, would be very helpful, I've read etc/keys and user / tuxbox not sure

    Thanks :thumbup: