Posts by scooby4466

    Hi,
    I've Vu solo2 with latest vti image running 2.3.0.I have just received a TivuSat Official SmarCam and Pre-Activated SmartCard.The box recognises card and cam but doesn't work.I was using 2.1.3 but the vendor told me to use 2.2.1 onwards,that is why I have changed to 2.3.0.The vendor also told to leave the box on Rai 4 incase the keys have changed,so the box has been on Rai 4 for a while now.Any ideas?

    If someone was helping themselves to my box what do I have to do,is it as simple as changing the password to the box,changing the ip address to the box or changing the port number.All my Flines end with { } { } clients address.

    Hi all,
    I've recently bought a vu solo 2 box having had a solo since they first came out.I have the latest VTI image but I have noticed occasionally it starts to try and record even though I haven't connected a hard drive to it yet.This results in the box turning the dish to a random sat and channel.
    The box for the most part is on stand by and the command for recordings to take priority is turned off.
    Is this an issue with the image?

    Here are a few channels showing the fight


    16E Arena Sport 2 HD (Cro)
    39E Arena Sport 4 (Serb)
    19.2EBein Sports France HD
    28.2E Sky Box Office / HD
    23.5E/0.8W TV Sport 1 (Cz/Svk)
    9E/0.8W/4W TV Sport 2 (Hun)
    4.8E TV3 Sport 2 (Den)/HD


    If anyone knows of anymore post them here

    Hi one and all
    Just to confirm,I couldn't get all channels until I installed a Satellite Signal Booster Amplifier,all good now.Got it off flea bay for a couple of pound.
    hope this helps somebody

    Hi all,I read somewhere I needed to hard wire the box to the router to set up the network first,so I have done that.Still having diffs (or fun,depending on your take) with the wifi bridge.

    Hi one and all,
    I am trying to configure an open media wifi bridge.The security my router uses is WEP (64 bit) with a 26 hex character.I am using the software which came with the bridge and have got to the third page where I have to put 10 keys in each of 4 boxes.I only have 26 keys in total,anybody got the solution?

    Hi one and all,I am trying to get the openbox s11 work with an openmedia wifi bridge.I have worked through the install of the wifi bridge and it seems to have connected to the network,although I didn't put a wep key in,it asked for a passphrase which I made up.Plug the wifi bridge into the openbox went to network,and applied.There was no message to say whether I connected or didn't.I ticked my cline and rebooted the box.When I went back into the cccam cfg my line was still offline.Where have I gone wrong? Thanks in advance.

    Hi,I have a similar problem with the usb hard drive.Although I can't go into device manager without the box crashing, therefore can not mount the hard drive.I am using VTI 3.2,I am wondering if I updated glass system utility this might solve my problem as well.So what do I do with the glass system utility file or can I download the plugin from the vti server?

    I get the same errors when trying to initialize and doing a filesystem check(this happen with two different hard drives,two different types).I haven't had a chance to do much to solve the problem but I was told if I flashed the box with an official original image I should be able to initialize the hard drive.Hope this helps.

    Using vti3.2,just selected the device manager and the box crashed every time.Removed the hard drive and can select the device manager.Now that I think about it the device manager crashed on older images with an old hard drive

    Hi all,I got a 1tb hard drive and am trying to mount onto a vu+ solo.I followed the tutorial and when doing a filesystem check I get this message;
    Unable to complete filesystem check.Error:Please Reboot
    And when doing the initialization I get this message;
    Unable to initialize harddisk.Error:Creating partition failed
    At the minute the harddrive is formatted to ntfs,do I need to format it to ext3 or fat32? Or do I have other issues?

    Hi,
    Just in the last week my cccam stops and doesn't restart.I haven't done anything with the cccam or messing with the box in weeks,I am using vti 2.6 with 2.2.1 cccam.Will I have to reflash the box or is there an easier solution?