Posts by kaspas

Hello community !

I need advice here !

Strong winds in ireland made my 2nd motorise system bad again, motor runs east - but no movement west ;(

So I bough T90 wave frontier

I have some questions - because setup of LNB and finding signal is not that easy i wanted ;( maybe somebody knows better way to get at least signal on central sat with T90

I do use original bracket on the wall - on which dish sits.... I think all installed correctly

I used satlex to calculate angles and elevation...

But had no success to get signal on any sat (only 28e I found with very strong signal - naturally ;) )

So I want to have 42e to 5w or 15w positions - idea is to have 13e in the centre. But I had no luck to get signal 13e even have it in the central position...

Question is can I place 13e in the centre of dish and search signal like for ordinary sat dish ? Or this will work differently ?

How to start to get signal with T90 just for 1 sat ? maybe somebody have experience with problem like that ?

Thanks !

Hello community !

After a days spent to adjust motor sat dish - just came up with solution -

Actually all trouble started after strong winds 120cm dish on technomate 2300 HH motor and tube on which dish was attached ! became loose !

somehow I missed this fact - I just tightened tube and was wondering why no focus --- as you see that`s the biggest problem tube is out of range and that

was the point I missed !

Thanks to all for help! I guess I need to get new motor - because adjust that tube in proper focus is not possible...

Hi ! Thanks Zilizila for info !

I think my adjustments needs to be more precise ... I think elevation angles are better now than yesterday .. I`m stikcking on motor latitude point which is 53.4 for me and dish declanation angle the best signal I got when adjusting Thor ...

so headaches starting when just few millimeters up - down declanation angle and back where I`m started no signal E good signal W and around...

sorry friends to annoying you... but definitely I will try to make it how it suppose to be...

Thanks for your efforts !!!

@jenseneverest Thanks mate for very useful guides !

I`m still working on setup - don`t know why this time so hard...

I have acceptable signal from 1w till 23e ( 28 as well but only 50% should be 99) but nothing 36-39-42 and 22w Algeria...

adjusting only screws... all angles stays like I made them on 1w (1w weakest signal I got 60% strong transponder 94%) - I will try to start from 5w next time I will do adjustments -

still when good on east getting bad on west... I will take a break for a few days I have long weekend off next week - will spend more time at that weekend

chris

0.8w in Ireland works ok as center sat (I tried few times before this dish)

5w might work as well never tried... but signal on 5w is good as well and maybe 5w is closer to true south compare to 0.8w

@jenseneverest

BYW what phone app you use for signal search ? If any ...

Cool ! will do - rain today, hopefully tomorrow afternoon...

Hello jenseneverest !

Yes I read the thread it is useful ... I think I have to get angle finder you adviced...

Pole bracket is ok - level is good !

Any advice from experience what method to use to correct problem ?

I mean get elevation 42e - then check 1w-5w then again ? do not touch motor elevation ?

Thx !

Thx for replay !

5w I thought I will start with 5w but honestly does this is really the problem ?

I will get 5w sure but how that will help me to resolve problem with 42e ?

When weather gets better I will try 5w just for sport but still can`t see what I`m doing wrong !

Hello !

I check as much I could info in this forum and google as well - but I did not find an answer to the problem...

Motor Technomate 2300 dish 1.1m primesat aluminium

Center sat I started 0.8w 12418 V got signal good when changing elevation can get strong signal 85-90%

- with elevation as from book motor 37 (Lat 53.4) dish bracket 22.4 nothing - changing bracket up to 25 signal goes up nearly 90%

ok leave it on it`s best moving to 13e and 16e - I had to move angle down 20 about 23 then I have signal acceptable for 16e - 13e and 1w

but no signal on 39e and 42e !

so when changing elevation down to 21 I got good signal from east 39 and 42 sat 70-80% but nothing on 1w now

so I tried 3 days one way - other way but still stuck if I have east sat then no picture on west and the way around...

Any advice how to solve ?

which elevation is I have to adjust - motor or dish ? preferable ?

what is best way- method to correct problem like this ?

------------------------------------------------------------------------------

At this moment I have Thor 5 strong transponder signal 72-74% but normaly nearly 88-90 and 16e weakest 44%-66% normaly can get up to 80% (but I have picture)

28e should be more than 100 but i have only 50%-60%

I see smth is wrong and need to be adjusted but after 3 days fail I really need advice - what I am missing ?

Thx for your time !

Hello !

2 servers with oscam - icecam have conflict

server nr1 is for de-sly the other server nr2 for 19e-13e ch.

Once I`m adding in oscam.server file server server nr2 lines de-sly stops working...

How to stop server nr2 decode de-sly ?

I`m using ATV 7.0 img with dreambox 920 oscam 11.678-r798

THX !

tomek there is no solution in that forum ...

Same problem here dreambox 920 sound ok pic frozen...

You know they changed pids or smth like thar recently...

I read somewhere it might be codec problem ???

BTW in pic I add 799 but it doesn`t help - it`s not comping up when in dreambox...

Hi !

I have a problem with ESP 4K (hotbird 13e 11258H)
audio pid for russian lang is missing after scan 799 is not coming up - any chance I can add it manually using e-chanelizer ? (I have full license)

Please advise !

Hello !

I do use latest unstable img. with dream elite extension panel and oscam 11682

All works great just oscam can not find softcam file ? biss is not opening ?

At this moment I copied sofcam file in etc/tuxbox/config chmod 644

Please any advice !

THX Seagen !

Works great !

I had to change DE to DE backup from piterfree (THX to man!) and plugins do their job as you suggested !

Good Job !

jeffxxl

possibly you already tried but no dream-elite do all for you itself !

Good img !

Hello !

Nearly solved !

Dream Elite img with their built in CI+ plug did the job and actually verimatrix module works great - opens everything fast and correctly

until I want to use my oscam emu ; (

is there solution how to make CI+ not to conflict with oscam emu ch ?

it looks like CI+ wants to decrypt ch. which is not in verimatrix - so t is not allowing oscam decrypt other providers ;(

Hello community !

Need an advice, support, help !

Just received XTRA TV (5e and 13e) Verimatrix by Neotion CI+ module - and it is activated !

But have problems to fully use it in dream. I am using dreambox 920 with Pure2 img.

So as I said module is activated with full sub !

problems are :

1 - Module opens just few ch. like Footbal 1 sd and hd / football 2 sd and hd both on 5e to open football 3 and setanta sports from 13e module say : your host is not fully CI+ compilant.

     I guess software is not right ? Smth is missing ?

2 - When module is in the box no FTA ch. opens ! Somehow module blocks FTA ch - how that is possible ? Any advice ?

3 - CI+ helper is installed - not much helping.

---------

1 - How to make CI+ fully compliant ?

2- How to make FTA ch. opening with module in the box ?

THX in advice !

Hi !

I`m using Pure2 love it !

Just a question about FNC plugins - FNC radio not working at all and HbbTV player do not opens properly.

Any advice to make them alive ?

Thanks in advance !