Hello
I want to ask something about remote control of dm800 and dm920
I use both receivers in one room. When I work with the dm800 remote, the dm920 is also controlled.
The dm920 remote only controls the dm920.
My question is with a change of image is there a chance to fix this. The remote of the dm 800 should send commands only to the dm800 without the dm920 being affected...???
try another image
for example openpli
I have opened a port in the router for the outside
In OpenWebif configuration enable HTTP Authentication and enable Authentication for streaming.
HTTP port and Streaming port must be open in the router.
Don`t use the default ports and have a very secure password as there is a risk a hacker can get access.
Yes, I created my port in the openwebif plugin, which I also opened in the router
There is no problem in the home network. Only when I try to get in from outside.
I have a problem with webinfo
When I'm on an internal network, everything is ok.
I have opened a port in the router for the outside ... With this port it works correctly in the internal network, but when I try outside my network it gives me this problem.
forbidden 403.6 ip address rejected webinfo
I have an openpli image if it matters
No ... I'm talking about the receiver's openwebif, not oscam
I have no problem with oscam info.
I mean I have an openpli 11 image
This work home internet
This over internet
The problem is that I install a new image, but the settings from the old image remain the same.
I want to install a new image but keep it clean
Hello
I have had this receiver for two days and I am satisfied
but I have a question
Is it normal to save the settings from the previous image after changing the image
my channel list is saved, my skin settings are saved
I have a dm800hd and there after changing the image it loads without any settings from the previous images
if not normal how to fix it
Nobody had this problem
I want to ask someone if he has this problem
I install all the picons on usb flash
after I upload them, they are all displayed until the moment when after restart the icons disappear completely or only individual ones are displayed.
my flash drive is 8GB, image openpli 2.1, dm800 pvr
So it happens to me like this ...
I install the image and after loading the logo the menu with languages is displayed. I choose for my country to restart and then follow a constant restart automatically and does not load the image
Have only en.po and it.po
I installed the image and after showing me the language selection it restarts and only the logo is displayed and does not start ...
now it just reboots without loading
After changing the version of Oscam, things got better, but until a few days ago.
Now my receiver started to load again.
I notice that when the load average holds values up to 1.5-2.5 it works stably. When it raises above 4.5 per minute and the receiver crashes.
I'm asking for help
I have a line for hotbird porn channels but whoever I go to the channel I wait 10-15 seconds for it to open
I think additional settings were put in oscam.dvbapi for faster opening
is there a way for the plugin to scan under tuner A: ALPS BSBE2 (DVB-S2) and not as in the plugin under tuner A
This plugin work dm800 hd pvr sim 3 ???
[reader]
label = bulsat
protocol = internal
device = /dev/sci0
caid = 4AEE
boxid = 12345678
detect = cd
mhz = 450
cardmhz = 2700
ident = 4AEE:000000
group = 2
emmcache = 1,1,2,0
[account]
user = dvbapi
pwd = dvbapi
keepalive = 1
au = 1
group = 1,2,3,4,5,6,7,8,9,10
[dvbapi]
enabled = 1
au = 1
pmt_mode = 0
request_mode = 1
user = Receiver
read_sdt = 2
boxtype = dreambox
i hvae my real local card
Oscam.config
[global]
logfile = /dev/tty
clienttimeout = 4000
clientmaxidle = 300
netprio = 1
nice = -1
maxlogsize = 1000
waitforcards = 1
preferlocalcards = 2
dropdups = 1
block_same_ip = 0
block_same_name = 0
ecmfmt = P: c:0p:s:d:i #ECM_L:l #CW=w HOP:j
disablecrccws_only_for = 098C:000000;09C4:000000;0E00:000000;0500:030B00,050F00;1884:000000;0B00:000000;1830:000000;092F:000000;0963:000000
[streamrelay]
stream_relay_enabled = 0
[dvbapi]
enabled = 1
au = 1
pmt_mode = 6
request_mode = 1
delayer = 60
user = dvbapi
read_sdt = 1
extended_cw_api = 2
[cccam]
port = ******
version = 2.3.0
build = 3165
[monitor]
appendchaninfo = 1
[newcamd]
port = ххххх@4AEE:000000
key = 0102030405060708091011121314
Oscam.server
[reader]
label = blala
protocol = cccam
device = xxxxxx,11222
user = xxx
password = xxxx
inactivitytimeout = 90
reconnecttimeout = 60
group = 1
cccversion = 2.1.2
cccmaxhops = 1
ccckeepalive = 1
cccreconnect = 11000
audisabled = 1
[reader]
label = we
protocol = newcamd
device = ip,1019
key = 0102030405060708091011121314
user = xxxxxx
password = xxxxx
inactivitytimeout = -1
disableserverfilter = 1
connectoninit = 1
cacheex_maxhop = 1
group = 1
Oscam.user
[account]
user = xxxx
pwd = xxxx
caid = 4AEE
group = 1
My receiver is crashing. The problem obviously comes from oscam.
After I let only 3-4 lines work, the problem disappeared. The question is, are there any settings. Or clearing the cache. Because I haven't had this problem before.
for a few days this number appeared to me at a feast
why it appeared and how to fix it
