Posts by tester2

hi guys any body know, I did the j-tag to dm500s, connections are ok, tuner shows ALPs, so when I click on 2alps then this screen shows & there is no progress starting like from 1%.........100%, just shows FLASH ERASE DONE at last.

so is there any body know, what I am missing in this j-tag process.

hopefully waiting for your reply

thanks

UPDATE : the below shows in CMD

C:\Documents and Settings\Themist8\Desktop\Jtagdm500AIO>jtagdm500 -m dm500 -e 00
:09:34:01:A4:3F
Dreambox Dm500 board initialize
Flash info. : INTEL Unknown
[dm500] reading CA:ca 00 01 06 20 21 46 00 09 34 20 21 78 06 04 ff
[CA] 6th mac addr byte is not redunderant, fixing it
Readed Config Area
Configuration Area
Mac Address: 00:09:34:20:21:46
Redunderant Mac Address: 20:21:46
Tuner Type alps
Mac Address Change Requested

Commit Config Area
Configuration Area
Mac Address: 00:09:34:01:a4:3f
Redunderant Mac Address: 01:a4:3f
Tuner Type alps
Erase Flash done

- - - Updated - - -

any body help me , what I have to do to flash boot loader in this dm500s

thanks

hi there,
yes it is the Password issue, and my Brother don't know the Password, because some one did the Programming close to his Home, so he put the Password on it, and he move to another place,.

So i like to know How to REMOVE Password on this dm500s, with out reloading IMAGE on it, please let me know, i will give a try.

just i want to REMOVE password on it & i want to load channel list on it.

Thanks

thanks a lot for your reply, that means it will work for dm500s....thanks

hi guys, can any body let me know.

can i use this Channel Editor on DM500S "dreamboxEDIT_without_setup_5.3.1.6"

please let me know this is good to use for DM500s or not.

Thanks for your replies

hi guys i need your help, i am trying to load channel list on my Brother DM500S Box from my Home via Teamviewer by using DBEdit, because he is missing so many channels last over year not updated his Box.

There is no problem establishing connection via Teamviewer to Remote PC. When i Run DBEdit and when i click on
here HTTP Port#21 -- "Test IP Connection" -- here connection established successfully
here FTP Port#21 -- "Test Username/Password" -- here unable to established the connection, because i am using default PORT#21 and i tried many other Port#s still unable to established connection.

So i like to know what is the "FTP Port#" i have to use via Teamviewer.

Thanks for your replies

hi mod, thanks for informing me, i did my introduce on this link, hope i did my introduce on right place
http://linuxsat-support.com/in…am-newbee-great-site.html

thanks

*******************
the reason i want to hide password, because in my home every body use same pc, so when any body click on dcc then password is already visible there, that connect to dm500s & any body mesh up the things eassly.

So i like to use diffrent software, which is more secure like PUTTY.

but still i did not get in to DM500S by using PUTTY, so i like to know "how to use this PUTTY for DM500s file transfer or Password change etc"

thanks

hi my friend, i run putty, after this, how to use to transfer frile from PC to DM500s.

if you let me know few steps, that will be great.

i never use like this softwares before. please let me know little more about this "how to use putty"

thanks

hi there,
i appricate for your fast reply, .
i alreay downloaded this
1)-wincsp portable
2)-and putty
after install which options i have to use for ftp transfers etc.
how to hide password by using above software while transfering file from pc to dm500s, please let me know.

if you know please let me know.

thanks for you fast repl.

hi guys , i need your help, i have dm500s, and i am using dcc,

in dcc i like to know how to hide password (i mean it should not in readable format, when i type password in it).

If i can't hide passowrd in dcc, then let me know which other proogram i can use, where i can hide my password, so that it should not visible.

Thanks for yyour replies