Posts by nicoda

Quote from rhurbarb

Quote from nicoda

Hi,

After many hours I installed new clean image - newnigma2 - dreambox 800se (original).

The plugin now is installed and opens without errors. However I can't connect either in TCP or UDP. Can someone please see the log and give me some help?

I also notice that with telnet command /tmp/init.d/openvpn stop the process does not stop! Verifying the log it is always in loop trying to connect.

Update: with another provider it has already connection

Display More

So you have it working ok now? Rhurbarb

Display More

Yes is currently working with a provider. I will test others as soon as I have some free time

Hi,

After many hours I installed new clean image - newnigma2 - dreambox 800se (original).

The plugin now is installed and opens without errors. However I can't connect either in TCP or UDP. Can someone please see the log and give me some help?

I also notice that with telnet command /tmp/init.d/openvpn stop the process does not stop! Verifying the log it is always in loop trying to connect.

Update: with another provider it has already connection

Quote from master G

Quote from nicoda

No module named subprocess

Try the attached python-subprocess.

Many thnaks for your support. I got this error "* opkg_prepare_file_for_install: Refusing to load file '/tmp/python-subprocess_2.7.18-r0_mips32el.ipk' as it matches the installed version of python-subprocess (2.7.18-r0)." :(

I don't have many options because the box is already old - dreambox 800se

I have the image "OpenPli-10.2-RT5370-DM800SE-ORIGINAL_mod_by_Monja-23.08.2020" which is here on the forum but feed are down. However i was able to install package by package and it opens already.

Based on log I have a stop at:

Sun Jan 30 16:31:53 2022 ROUTE_GATEWAY 192.168.1.1/255.255.255.0 IFACE=eth0 HWADDR=00:XX:xx:xx:xx:xx

Sun Jan 30 16:31:53 2022 ERROR: Cannot open TUN/TAP dev /dev/net/tun: No such file or directory (errno=2)

Sun Jan 30 16:31:53 2022 Exiting due to fatal error

Is there any idea about this. I search for a fix on that but i doesn't work.

Regards

Quote from rhurbarb

Quote from salomaoa

Hello All

Installed version 1.1.4 on a Zgemma H9.2H SE running openpli 8.1 (couldn't install version 1.1.6).

The very first time I run the plugin and started openvpn it conected fine to my vpn. The proble is, after restarting my enigma receiver, I could not access internet anymore. My receiver receives no IP (if HDCP is enable) and if I set DHCP to off it wont accept the imputed manual IP. Doing a network test shows that I have no IP and am not connected to the internet.

More, if I try to change my network configuration (I have bothe LAN an wifi interfaces) my receiver crashes.

I had to re-install OpenPli and started everything from the begenning, with the same result.

If I run OpenSpa instead of OpenPli it will run OK!

So, is there any way I can set it properly in a OpnenPli image?

Salomao

Display More

Hi I have vpnmanager working here on Openpli 7.3...with version 1.14 . After 3 nights of pulling my hair out I finally done it...kinda lost what I done but I can trace my tracks for you if you still havn't sorted yours out.

Display More

Hi Did you have a problem after installing the plugin saying"No module named subprocess" ? I already have v.1.1.4 running on dreambox 800SE but due to an error I needed to re-install the image again and I never be able to install the plugin

opkg update - feeds are down? Can someone tell me any other backup source please?

Hi,

I'm trying to reinstall vpn manager plugin but it never works. I have the ipk into tmp and then Software-Install extensions from /tmp and it doesn't get any error but ever after reboot the plugin doesn't appear. Any ideia about this?

hi everyone. A few months ago I was able to configure the vpn manager plugin with proton vpn free servers. However today i don't have more connection. Should I re-install the plugin? The vpn data I reviewed again and they seem fine.