Posts by tiku_2

I Had flashed two different images one via browser and another via jaspher flasher but i am still getting Bios No Ca Found on the Panel Display.

1.openatv-6.4-dm800se-sim2-20230923

2..BlackHole-3.0.2C_DM800se-sim2-SSl84D-20160625-Houara

ok i got the box flashed, now i can see dreambox console in my browser, now plese kindly guide me which is the best image i should flash in my dreambox?

i have all three box with 2.10 sim two of them are from sunray and one from another company. Please also tell me whether i should flash new image via browser or jaspher flasher?

thanks

Quote

That's your mistake... IT MUST have RJ45 to the Router as well... otherwise how can you find the IP address of your box in your network if it's NOT connected to the network ?

Sorry My mistake. I had Flashed PLI Image on DM800HDse A8P Sim with only one RJ45 Cable because i have only one cable with me, Now I remember what i did, I had connected my Laptop to router via Wifi And the Dreambox DM800HDse with RJ45 cable, in that way i got the Correct Box Ip, Because i have cross checked in my TP Link Router Setup -DHCP-Client Menu, It Showed Dreambox Name and also the IP Assign to It.

Quote from toysoft

Check the frontpanel of the box, do you see the IP address on it ?

How did you connect the network part ? DM800HDse with RJ45 to the router/modem, and computer to the router/modem as well with RJ45 ?

Yes i see ip address in front panel of the box.

My laptop is connected to my router via Rj45 and

DM800HDse is only connected to laptop via mini com port (service) NO RJ45 CABLE.

the box is in HTTP mode, I typed the ip 192.168.0.106 in my chrome and edge browser, but its not opening.

what next?, see the second pic if i select 84d.nfi file and click on flash, it says calclating checksum, I can see the ip on the dm800hdse panel display.

Quote

you quoted 800 then you say 800if...???...what are you doing is unknown

What the thread title says its the model which I have, I didn't knew i have to write complete model in every reply, also I have mention clone from sunray which speaks itself that its without RS232 port.

piterfree

No sir 800 clone don't have a RS232, Infact it has mini usn port which is printed service on it, and it is use for communicating with the box Usb-Uart.

toysoft

Ok i rebooted the router, connected all the cables, used Jaspher v 1.1, but still no Luck, No Response from the box But the Display LCD Says No Ca Found, where as again connected working DM800 in jaspher flasher and it initiated http; Box Detected dm800 and the green bar goes full.

toysoft

Why do I have to reboot my router? , I have one working DM800hd which i revived with same RJ45 cable few days back, its still getting detected if i connect using Dreamup, Sunray Flasher.

Also when i power up working dreambox I can see the new ip in the DHCP Client Menu of my router setup but thats not the case with these two. So no chance of damaged cable.

piterfree

I am using Windows 10 everything is installed correclty as i said if i connect mini usb it gets detected in Device Manager, morevover I just revived one DM800hd with same cables 2-3 days back.

Hello Friends, I have a couple of DM800HDse (Clone from Sunray SIM2/2.10), and all are hanged on No Ca Found.

Now my problem is that, mini usb connection is deteced in com port & shows Silicon Lab cp210x port(xx), But i am not getting any IP From the Lan

Cable attached to my router, and if i uncheck Use Network in Sunray Flasup Tool and Click connect it says connection prepared now switch on the dreambox!, but when i power up my dreambox there is no response from the box, No http:, No IP on the dreambox Lcd, No flashing Ethernet Leds in back of Dreambox. I Think My Box Is Hard Bricked, Can One Help Me Out.?

Note: I also Have A Case Interface 3, but there is nothing on the Net Regarding how to Revive DM800HD with Cas Interface 3,

I See three Different 7pin, 10pin & 14 pin jtagging connectors in the Dreambox Motherboard, but don't know which one is for Flashing Bootloader and what are the pin connections from Cas3 to Dreambox

Thanks

Thanks s3n0 for detail explanation,

My stb has a single tuner so the first probablity is zero.

Now if someone has stolen my account is possible, because i have bought a mini panel to generate my personal cline, and i haven't changed the login user/password also the seller is a third party and he knows my login credentials, I am not buying directly from the main seller which is in Sri Lanka.

Also I login from my Android phone so there is a good chance of my login credentials been stolen via any app.

The third reason which is change of ip address is also possible because my IP is not static, if there is a power shutdown or i reboot my router, there is a new IP. But this dynamic ip problem is always there ever since i started using internet from years, and blocking of cline is started recently from 2-3 months.

Hello,

My Problem is that, i Have purchased a cline and was using it in a normal stb Openbox V8S, now from few months the provider has blocked

my cline twice and i have to generate new cline, the reason he is saying the my cline is being re--shared, now i don't know, how did he came to the conclusion, may be fast ECM, or Fast zapping of the channels. So i am scared to use any cline in my Openbox stb.

Now i want to use a new cline in Dreambox800HD, Is there any way that i Can be 100 percent sure that my future cline will not be blocked if i use a script in the cccam.cfg file, or MGcamd file.

My provider sell Cline also MGcamd Oscam Line.

Thanks

Quote from hecha71

Quote from tiku_2

Thanks, So which one form the Two Images You Gave Above should I Flash Original or Clone?

Original

Hello Friends, I have flashed the original pli 11.2 in my DM800HDse, A8P Sim, the Box Rebooted Fine, but i have two problems

1. The LCD Display on the Box is Blank, There is nothing on Box Panal LCD

2, IF i Scan one frequency on the one transponder, it tunes all the channels, for exapmle 20-25 channels

then on the same Sat, if I Scan another frequency the previous channels gets deleted (Not Visible), It Only shows

the last tuned frequency channels only, what will be the problem?

I tried with No Clear option also, but same results. Please Somebody Kindly Help Me.

Thanks.

Quote from bobimilo

Quote from tiku_2

Now my problem is that since its hanged on boot logo, No Image is Detected via USB, be it Open ATV, PureE2 , Openspa, Nothing flashes on the Screen saying New Update Found.

Pleaase follow this tutorial in this link:

[TUTO] How To flash/update Qviart Lunix 4K – ENIGMA2

I think you have not read my request carefully ,at present i cannot upload any image via USB, USB Flash drive is not detectable,

I wan't an alternate way of installing the Firmware Besides the USB.

Hello Friends, i am Having Qviart Lunix, it was running Open Pli firmware from 2017, i updated with the latest version openpli-9.0-release-lunix-20241027_usb, the Installation was smooth & successful but after the reboot now the stb is hanged on Qviart Linux Boot Logo, tried 2-3 times power on-off

it just flashes twice on the Boot Logo and don't go further, No Pli Home Menu.

Further searching on the pli forum came to know that they don't have the original driver from the manufacturer, so the new images after 7.1 is not compatible, where as Open ATV IMAGE

works.

Now my problem is that since its hanged on boot logo, No Image is Detected via USB, be it Open ATV, PureE2 , Openspa, Nothing flashes on the Screen saying New Update Found,

The Only thing is that I can Communicate with the stb Via WINSCP and Putty, i can see all the folders and transfer files.

I want to know is there any way i can install New Image Open Atv via file transfer, if yes than please tell me how? and in in which folder should i Place the Image Firmware,

and the Syntax Command,

Thanks.

Hello friends, Please Anyone can upload the stock firmware of KIII Pro PC File Version
KIII_PRO_AVL6862-NHG47L-20180908.182748.V0213.img,Since all the previous uploads are obsolete now.
Thanks.

Quote from hecha71

Quote from tiku_2

Of Th Sim Attached. Its A8P, Also please anyone guide me which is the most stable image for my box.

This is a copy of the original A8P sim, I have exactly the same sim installed in 800se, all the images collected under the original are filled in, and the most normal image with a working feed and the ability to install some new plugins and also implement iptv viewing -these are builds from xingchong!you.

Thanks, So which one form the Two Images You Gave Above should I Flash Original or Clone?

Hello Friends, i have got a Dreambox 800 HDse from my friend, How do i know whether its an Original Or Clone?, i see a couple of chinese sticker on the PCB, here is the Pic Of Th Sim Attached. Its A8P, Also please anyone guide me which is the most stable image for my box.

Thanks.

Hello friends, I have a very little knowledge about Linux OS, Can any friend provide me its Full Backup of Zgemma H9S (Single Sat Tuner) , with preloaded all the Cams, Emulators, Live TV Plugins and Addons, or with wooshbuild Infinity in Openatv 6.2 or later version, I would be very much Obliged and Thankful,.

Thanks.:fingers crossed: