Posts by newtolinux

looks like they are up to another bout of card turn offs then !!!! I guarantee your card took a killer emm yesterday . This is why its important to not allow emm's from cccam. This has been documented for over 1 year now on various forums. Not to mention recent activity with cccam no longer opening some channels ; but only oscam opening them. The message you have got on your screen is so you call them !!!!!!!!!!!!!!!!!

When you call you've been working away for 6 weeks so your box has been turned off etc at mains to save power etc ...... say "you got back today and turned box back on and got this message about wrong card and your confused as its the same card you have always used" ...... play dumb !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

report back the response you get from sly

regards
new2

just ensure you password everything if your remote accessing !!

and how many entitlement teers did you have before ??
sounds like your card has received a bad emm . Not to be rude but is your bill paid all up to date ?

dd-wrt great firmware . turns a cheapie router into a ?600 spec router . So stable aswell . You can also run oscam in these routers !!!!

or you could add as a global block in newer versions of cccam i believe rather than on every c line

ok , when you run cccam info and look at your card in reader section what dates do the entitlements show ??

have you used your reader with other cards before ????? As maybe the reader has a fault . Also look at your mhz settings as i dont believe via cards will read at 6mhz

regards

good luck

hi rom,

are you using oscam as main card server and passing to mgcamd in vu duo or are you proposing to use oscam with dvbapi function

regards

flyman have you got this issue sorted now ??

regards

new2

you have got two cards on same device port in your configs. look at your line .... device =

regards

new2

I've no experience of your local myself but this problem has been well documented on other forums for some time.
You are running cccam to read your sly uk and pass emm updates to the card !!!!!!! Very very bad idea !!!!! There is no facility within older cccam versions to block killer emm's which sly send out over the network.
The message you are getting on original box means your card needs a repair signal sending from *** to pair the box with card . Did your entitlements run out on card ?????????????????????? Do you run a multiroom subscription ???????????????? When you put your card back in original box was the original box connected to the phoneline ?????????????????

give your replies to questions please

regards

new2

more info required . dont really understand your question

regards

new2

you can ofcourse use your receiver as a card server . Be careful though of what receiver and what card !!!!!! Certain receivers have the wrong voltage to the reader which can cause certain cards to cook if read in them .

please post back receiver you intend on using and which card

regards

new2

firstly why are you using cccam 2.0.4 ( no support for new cards !!!!! )
why have you updated firmware on smargo as 1.3 is the best to use ???
what card are you trying to read ?
have you set your smargo into normal or dreambox mode from smargo tools ?

regards

new2

it depends on your peers of peers and so on . Your better for stability with only 0:0:2 on shares in my opinion anyway.

regards

new2

there must be an option in your router for dhcp addressing with ranges etc.

Look for this option asap.

Make sure your dream is on a static ip as you are setting up forwarding rules etc.

Ensure for instance that your dhcp range is in fact on the 192.168.2.1 - 192.168.2.100 ( for example )
The other settings your posting is what your isp has assigned and is irrelevant to your local lan
What forwarding rules have you setup in your belkin and under what section ?

regards

new2

hi botak,

You need to get yourself shares with friends etc to begin with . But over in malyasia i dont know what dish footprints you would pick up or what satellite packages you would be looking for. It is not as simple as buying a box and it gives you free TV. You need a network of friends to share amongst etc. A standard cccam.cfg is just that !!! empty and only contains some guidance with information. You need to determine firstly what you want to achieve with your new box

regards

new2

just flash it via one of the clone tutorials from this site and choose the appropriate image . Like ten had said new images bring newer drivers and support for addons etc.... There is no harm in upgrading a bootloader it will only do good things for your box !!!My only advice after messing with mine for hours yesterday is "if it aint broke don't fix it" . My box was running fine but i fancied a change of image . A little headache but great support from guys here as usual and box is all good :)

regards

new2

I would imagine even if you could get to the bootloader it would read the flash image and report back an error and not continue. Obviosely you could try it but its very very likely that it won't take the image or you could brick the box. Would leave alone in my opinion unless you got money that grows on trees lol

regards

new2

daz defiantely get one with an external psu as quoted above .

regards

new2