Brauchst doch nur die Oscam datei bei usr/bin reinkopieren .Vorher so umbenennen wie die alte Oscam hiess zB beim VTI: oscam-unstable und Rechte auf 755 setzen.
Posts by bak07
-
-
What is Ncam ?
Is that like Mgcamd? -
ATV Softcam feed is now with Mgcamd1.35a for Solo 4k , but it dont work with OpenATV 5.3 only with old 5.1
-
Using BH,VTI,OpenATV always Mgcamd runs better and after deepstandby.Oscam mostly bad after Deepstandby and must startet manually to work.And Zapping is faster at scambeld Channels.
At te Moment I use ATV 5.1 or BH 4.0 both works fine with Mgcamd 1.35a but OpenATV have stopped Updates for 5.1.
They Support only Open ATV 5.3 and for this Version there is no working Mgcamd .Same as with New Vixx -
Mgcamd runs better with my Line and always started after Deepstandby.
Oscam sometimes dont start afer cold boot of Box .Thats worse fore timer Recording
And much more possibilitys for a Mistake with Oscam as with Mgcamd. -
I dont have the Profession to do this
I am thankful that Your IPK 1.35 workes in old ATV 5.1 and hoping that Someone can mahge it for New Images too.PS
Greatings from Berlin to Northern Ireland and Congratilations for being qualified for Soccer EM -
He asked for Mgcamd not for Oscam
He will knew that Oscam possible but that does not help him if he wants Mgcamd
please Answer his Question
This Answer ist as if Someone asked for a Bus to come to a Place and the Anwer was "take a taxi"
The Captain from Open ATV told mi that for the new OE Alliance Images it needed Mgcamd 1.38 as 1.35a dont works anymore as the libs are others as the New Ones needed.
-
But without Mgcamd
-
Oscam makes the Problem that after Deepstandby the Cam dont starts automaticcly.
Thats bad for using TimerMgcamd starts and run well in Solo4k and startets automaticlly after Deepstandby,but only in older Images like OpenATV 5.1 not in 5.3
-
Searching for a working Mgacamd for a Solo 4k Box for OpenATV 5.3
In old OpenATV 5.1 it did work but not with 5.3
-
Has someone a working Mgcamd for OpenATV 5.3 ?
The old OpenATV 5.1 did work with Mgcamd but not the New 5.3
- - - Updated - - -
I Used this but it dont work with Solo 4k
2) The decision in principle is very simple, download libu libcrypto.so.0.9.8 of the enclosure (attachment to the post) and throws the path: / usr / lib /
3) Give the file attributes 755
4) Go to the telnet and give the command: ln -s libcrypto.so.0.9.8 /usr/lib/libcrypto.so.0.9.7
5) After doing a reboot and run Enigma 2 -
And not works in OpenATV 5.3
-
same as with ATV 5.2
-
Open ATV 5.2 it dont run ,
but it is in the Cam Menü after Installing,
it is named Mgcamd 138d ? -
Wetek has no FBC Tuners
-
And for OpenATV 5.2 ??
-
Best Way is someone load a Backup Image with working Mgcamd for OpenATV or Vixx in this Forum
-
Without FBC Tuner its out of Interest
-
I am in Opposide to Hans review
The Box ist good but the Remote is rubbish -
Best would be a backup image with including Mgcamd for OpenATV