Posts by Untouchable

  • Newbie flash

    You didnt write if is clone or original, but anyway
    There are a lot of images to select. Just watch out version of image and of your box.


    Also read users comments - helps a lot!!!

  • card updated issue

    You have to change - edit G: and P:
    Cause by default MGCAMD running with newcamd protocol.


    G: 32 or 33 # (32 cccamd netclient, card list saved as /tmp/cccamd.info )
    P: 02 # ( 02 cccamd, newcamd, camd3, gbox, radegast)


    On this set you can read first cline....
    I dont use anymore mgcamd, but if you still got problems message me and i will sent you my working backup conf.

  • How to ignore provider?

    Well...
    Nice question!
    I dont use mgcamd any more but as i know mgcamd use "ignore.list" file
    So an example of your case is to add on ignore.list X: { 09 63 } but this is not ok 100%.
    1.35a for example use cccamd.list and newcamd.list
    You can see my configuration of mgcamd for optimize working with both lines C and N
    Expirementals are with G: and P: lines


    Try out and if no results here we go again

  • Cccam recommendations for Cloned DM500S

    Another alternative :


    A clone that i got for tests only got nemesis 4.4 and running perfectly.
    Just keep away from gemini images, older than 4.20 to be safe of flash damage.
    In any case your can re-alive it back by jtag but, i hate solderings and headaches!!

  • Kill command for Cccam ?

    And another alternative for cccam:


    To stop cccam :
    cd /var/bin (path of your cam)
    killall CCcam_... (_...is the version od cccam you got, an example is killall CCcam_2.1.3)


    To start cccam :
    /var/bin CCcam_... &


    I hope that helps you a lot
    Good luck.

  • cccam security?

    Yeap, nice post.
    It is available through proxy tunneling.
    A good example is with ssh and dropbear, but peers that connect must also accept it.
    Soon i will find a little free time to make a detailed post how to.

  • connect mgcamd on dm500s with remote cccam server

    What i test till now and working:
    Best way to connect to cccam srv is to use Mgcamd 1.35a
    That was mine config, working also on cccam above 2.1.1


    # EMM messages
    # 00 don't show any EMMs (default)
    # 01 show only valid EMMs
    # 02 show valid and bad EMMs with complete data display
    M: { 01 }


    # ECM messages
    # 00 don't show anything about ecm
    # 01 normal mode, show pids processed, decoded ecm and cw
    # 02 verbose mode, show valid and bad ECMs with data
    C: { 01 }


    # AU
    # 00 disable, no emm pids processed
    # 01 enable, emm pids always processed for soft-au and shared cards
    # 02 auto, emm started only if channel cant be decoded
    # 03 process emm pids for network cards update only
    A: { 02 }


    # key update (sum 01 or 02 with 04)
    # 01 update only new keys, default setting
    # 02 update all keys (used for valid PMK checking)
    # 04 enable TPS au
    # + tps SID, which pmt pid contains au pid
    #U: { 01 } 0x12c0


    # config files folder (softcam, autoroll, ignore/priority)
    # 00 files in /var/keys
    # 01 files in /tmp
    #T: { 00 }


    # network mode, use summ for several clients
    # 00 no network (default)
    # 01 newcamd netclient
    # 02 radegast netclient
    # 04 camd3 netclient
    # 08 gbox netclient
    # 32 cccamd netclient, card list saved as /tmp/cccamd.info
    # (ECM only, supported server version up to 2.1.1, later not work)
    G: { 33 }


    # network retry, use summ for several options
    # 00 disable
    # 01 retry every new ecm
    # 02 try to connect to offline shares every Q: seconds
    # 04 try to detect and fast reconnect to lost (and not used atm) server
    # + XX messages number and YY seconds to reconnect
    # mg will reconnect to server, if no answer to last XX ecm/keepalive or
    # if no answer for last ecm or keepalive sent for YY seconds
    # set to 0 to disable
    N: { 07 } 5 30


    # network ecm timeout in seconds
    K: { 05 }


    # newcamd dead routes connect retry, sec
    Q: { 600 }


    # network shares priority
    # 00 gbox, newcamd, cccamd, radegast, camd3 (default)
    # 01 camd3, radegast, cccamd, gbox, newcamd
    # 02 cccamd, newcamd, camd3, gbox, radegast
    P: { 00 }


    # on screen display type
    # 00 No OSD (default)
    # 01 neutrino
    # 02 enigma
    # 03 relook
    # + user password for http auth
    O: { 00 } username password


    # on screen display Options, summ of:
    # 01 show emu ecm
    # 02 show network shares messages
    # 04 show decoding failed / fta
    # 08 show emm keys update
    # + web port to use for osd
    S: { 03 } 80


    # Log option, summ of:
    # 00 off
    # 01 network udp log
    # 02 log to console
    # 04 file, appended ! delete it by yourself, before it eat all your hdd
    # + IP udp-port log-file-name
    L: { 00 } 172.16.1.1 28007 /tmp/mgcamd.log


    # keep ecm cache, seconds
    # every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,
    # for openbox/elanvision users with remote shares make sense to set it higher than default value,
    # to not hammer cards while timeshifting or playing crypted recordings.
    E: { 15 }


    # cache option, summ of:
    # 00 Off (default)
    # 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list
    # 02 Ecm data cache, remember CW for (E:) time
    # 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart
    H: { 07 }


    # reread files, summ of:
    # 00 No (default)
    # 01 reread config file on channel change (including priority and ignore, but not replace/cache)
    # 02 reread SoftCam.Key on channel change
    # 04 reread SoftCam.Key if file changed
    R: { 00 }


    # debug, summ of
    # 00 off (default)
    # 01 debug ecm
    # 02 debug emm
    # 04 debug network ecm
    # 08 debug network emm
    # 16 debug network login
    # 32 show mem/cpu stats every 1 min
    # 64 add timestamp to log messages
    D: { 00 }


    # box type
    # 00 autodetect, change only if you think wrong type detected.
    # 01 dbox2
    # 02 dreambox
    # 03 triple-dragon
    # 04 relook
    # 05 openbox
    # 06 dreambox/mips
    # 08 stapi/kathrein
    # 09 stapi/ipbox
    # 11 stapi/openbox
    B: { 00 }


    # map all 180x nagra caids to 1801
    # default is 01
    F: { 00 }


    You have to remove or rename cccam.cfg if you got one, and not using softcam (empty).
    Good luck!