Posts by neil_1980

  • FBC OpenATV OpenWebIf Issue

    Quote from abu baniaz

    After you describe the wiring, please also describe the tuner configuration for every tuner. They must match each other.


    The tuner with the Unicable LNB must be set as Unicable. If the other tuner has a direct wire from 19.2 with no switches, that tuner must be set as simple, single, 19.2.

    I think I've possibly sorted it....


    Tuner A is set as unicable with 28.2 and the manufacturer and model of the LNB That has a single coax straight to the Unicable LNB

    Tuner B is set as simple 19.2 and single coax straight to the plane old standard LNB

    Tuners C to H....

    for some reason if I leave as FBC Automatic they dont seem to do anything... multiple recordings at same time on channels on 28.2 result in an message about a conflict in recording... so I'd changed them to FBC SCR, 28.2 and the rest of the details seem to populate from Tuner A as the manufacturer details are all there.


    However what I hadn't done is chance the Channel so they were all set to SCR 1.... I've since read elsewhere that these need to be differentt... changing them just to SCR 2, and SCR 3 etc seems to have fixed my issues

  • FBC OpenATV OpenWebIf Issue

    Sorry if extra details have confused.


    The sky hybrid lnb is now sat in a cupboard doing nothing. I only mentioned that as streaming was working using that (the legacy ports not wideband)


    Pointing at 28.2 is one of these (https://store.gigablue.de/sat-…-2-legacy-uhd-4k-lnb.html) which is configured as FBC.


    Pointing at 19.2 is a standard LNB.


    It’s one dish but with two LNB’s on a bracket… to be clear they both work fine and get the relevant channels it’s just streaming when using the FBC lnb that’s an issue but sounds more like a config issue my end even though it’s playing and recording ok on tv

  • FBC OpenATV OpenWebIf Issue

    Hi All,


    Hopefully someone can help as I'm kind of stuck on what I think is an FBC issue (or FBC setup issue) rather than software.


    I recently bought a Gigablue UHB Quad 4K Pro which was connected to a sky hybrid LNB on Tuner A whilst getting it all set up which whilst it was connected this way I could stream throug Openwebif or the gigablue iPhone app and all was good.


    To cut a very long story short I currently have a standard LNB connected to Tuner B and a new FBC tuner connected to Tuner A.


    If I try and stream something on a channel through Tuner B through a browser or Gigablue App or Kodi it all works fine, Anything on Tuner A though and the stream shows nothing but the TV connected to the box becomes a stuttery mess... looking at the signal on satellite finder the signal bars keep cutting gin and out to 0%. Kill the (none existent stream) and change channel to something else and back and the signal remains solid.


    Im using OpenATV 7.5.1 but I've just tried OpenATV 7.4 and Teamblue 7.5 in different slots and have the same issue


    I did initially think this was an OpenWebif issue but the fact it only seems to be an issue with the FBC LNB I'm wondering if im likely to be missing anything configuration wise? When I initially set this up tuners C on were set to Auto but it wouldn't allow me to record multiple channels (Forget the exact message but was something relating to a recording clash). I changed C onwards from Auto to FBC and using LNB 1 which seems to have fixed that but wondering if I've missed anything like this for streaming?


    Neil

  • Control TV Volume From Remote

    Quote from urie
    Quote from neil_1980

    Well it’s actually an AV amp rather than a TV it’s going through… and whenever I’ve tried CEC with anything in the past I’ve ended up with weirdness with other things so have it turned off

    Sorry cannot help with that but perhaps that should have been your question rather that tv hopefully someone may know. Older remote was a different beast it was universal remote. And to be honest hopfully they can bring something simillar for the pro with bluetooth.

    In fairness the question (can you program the volume buttons to work off a tv code like the previous remote) is the same regardless of if it’s a TV or an AV amp… but thanks for taking the time to reply anyway

  • Control TV Volume From Remote

    Hi all,


    I don't suppose anyone knows if it's possible (and if so how?) to get the remote to control the TV volume without using CEC?


    Previous versions it says to hold the TV button down and then enter the relevant code but the newer remote doesnt seem to have a TV button.


    5715_4.jpg