Getting rid of CCcam altogether and using Oscam with anticasc enabled will stop resharing.
Posts by mkhan
-
-
Seems to be....Is this for sending the signal to another TV?
No. My TV broke down recently and I had to replace it with a standard one until my HD set was fixed, this is when I noticed the problem.
When my HD set was repaired I tried connecting the duo to the TV via the scart socket and got the same result as the standard def TV.
hdmi is needed on a hdmi box as skins etc are designed around hdmi resolutions. You will always have probs if you go for scart out
new2
It's pointless them having scarts on the receiver if you can't make proper use of them. -
HDMI to your TV! Are you connecting it to a modern TV? You should have an HDMI connection on the back of your TV which you can connect the VU+ to!
I'm currently using it via the hdmi cable and the menus don't get cut off but when I plug in a scart socket it gets cut off.
Is hdmi connection the only way everything will be displayed properly on screen? -
Can explain a bit more about what you mean by hdmi out?
-
I don't have any phono plugs therefore I haven't tested it but I guess I would get the same result I did with the scart socket.
-
I've tried settings in the TV and no joy. I changed to another skin, it sorted out the info bar and menu due to them being centered else they would have been cut off if they weren't centered. It's not that bad now however certain extended menus are cut off.
I hope they design a skin for SD TV's in case anyone wants to use a scart else theres no point in having a scart socket on the receiver.
-
When I use HDMI cable the picture is fine but when I switch to scart the image is too far stretched towards the left. It makes it difficult to read the writting on the menus due to most of it being cut off. I've tried AV settings, the problem is still there.
Is this a common problem with vu duo if using a scart?
-
-
These are my configs and screen shots.
Oscam.Conf
[global]
logfile = stdout
disablelog = 0
disableuserfile = 0
usrfileflag = 0
clienttimeout = 5000
fallbacktimeout = 2500
clientmaxidle = 120
failbantime = 30
cachedelay = 120
bindwait = 120
netprio = 0
clientdyndns = 0
resolvedelay = 30
unlockparental = 0
nice = -1
serialreadertimeout = 1500
maxlogsize = 50
waitforcards = 1
preferlocalcards = 1
saveinithistory = 1
readerrestartseconds = 5
lb_mode = 1
lb_save = 0
lb_nbest_readers = 2
lb_nfb_readers = 1
lb_min_ecmcount = 5
lb_max_ecmcount = 500
lb_reopen_seconds = 900
resolvegethostbyname = 0
failbantime = 10
double_check = 1[webif]
httpport = 16002
httpuser =
httppwd =
httprefresh = 10
httpallowed = 192.168.1.28-192.168.0.xx
httphideidleclients = 1
httpreadonly = 0[cs357x]
Port = 18000
server1p = 192.168.1.28Oscam.Server
[reader]
label = slot1
protocol = internal
device = /dev/sci0
boxid =
detect = cd
mhz = 357
cardmhz = 357
blockemm-u = 0
blockemm-s = 0
blockemm-g = 1
blockemm-unknown = 1
emmcache = 1,3,2
group = 1
caid = 0963Oscam.User
[account]
user = test
pwd = 12345
disabled = 0
group = 1
uniq = 1
sleep = 0
au = slot1
caid = 0963CCcam.cfg
SERVER LISTEN PORT : 17000
ALLOW TELNETINFO: yes
ALLOW WEBINFO: yes
WEBINFO USERNAME :
WEBINFO PASSWORD :
TELNETINFO USERNAME :
TELNETINFO PASSWORD :
TELNETINFO LISTEN PORT : 16000
WEBINFO LISTEN PORT : 16001
ZAP OSD TIME :5
OSD USERNAME :
OSD PORT :80
SHOW TIMING : yes
DEBUG : yes
NEWCAMD CONF :no
DISABLE EMM : no
MINI OSD : no
SOFTKEY FILE : /var/keys/SoftCam.Key
AUTOROLL FILE : /var/keys/AutoRoll.Key
CAID PRIO FILE : /var/etc/CCcam.prio
PROVIDERINFO FILE : /var/etc/CCcam.providers
CHANNELINFO FILE : /var/etc/CCcam.channelinf
LOG WARNINGS : /tmp/warnings.txtL: 127.0.0.1 18000 test 12345 0963 000000
-
It's been 8 days since I paid my bill and I usually receive emms to update the entitlements on the card by now. I have Oscam+CCcam running on the same receiver using Camd3 protocol and Oscam in Webif is reporting that AU is ON.
Have I missed anything out in the config files?
