Welcome.
I have a problem with Alien2. I had the "Boot" so I wanted to fix it.
By Putty typed command :
set bootargs console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00*:06:37:04:15:00
ip=192.168.40.83:192.168.40.19*:192.168.40.1:255.255.0.0:lh:e*th0:off
stmmaceth=msglvl:0,phyaddr:1,w*atchdog:5000 bigphysarea=6000
and
nboot.i 0x80000000 0 0x00100000 ;bootm 0x80000000
Spark began to work.
I did upgrade online 1.2.58 Spark Europe, but then when you start shoved PowerOff (remote).
The display appeared to mark time and timer, the red LED.
When you turn ON again, "BOOT".
You're welcome to help as soft upload via RS232 or how to run a tuner.
Board: STx7105-PDK [32-bit mode]
U-Boot 1.3.1-g72483220 (Jan 17 2012 - 17:10:49) - stm23_0051 - YW_1.1.003-9-g7248322 overclock
DRAM: 256 MiB
NAND: Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
512 MiB
SPI: ERROR: Unknown SPI Device detected, devid = 0x1f, 0x46, 0x02
ERROR: Offset out of range (max=0xffffffff)
In: serial
Out: serial
Err: serial
Ident ic exist
Ident ic get stb id
IdentID : 0c 00 0a 00 00 1a 63
PDK7105> set bootargs console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00*:06:37:04:15:00
PDK7105> 168.40.1:255.255.0.0:lh:e*th0:off
Unknown command '168.40.1:255.255.0.0:lh:e*th0:off' - try 'help'
PDK7105>
PDK7105> stmmaceth=msglvl:0,phyaddr:1,w*atchdog:5000 bigphysarea=6000
PDK7105> nboot.i 0x80000000 0 0x00100000 ;bootm 0x80000000
Loading from NAND 512MiB 3,3V 8-bit, offset 0x100000
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5899022 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 3001608 Bytes = 2.9 MiB
Image 1: 2897402 Bytes = 2.8 MiB
## Booting image at 80000000 ...
Image Name: Kernel-Ramdisk-Image
Image Type: SuperH Linux Multi-File Image (gzip compressed)
Data Size: 5899022 Bytes = 5.6 MiB
Load Address: 80800000
Entry Point: 80801000
Contents:
Image 0: 3001608 Bytes = 2.9 MiB
Image 1: 2897402 Bytes = 2.8 MiB
Verifying Checksum ... OK
Uncompressing Multi-File Image ... OK
stmac_phy_get_addr(): id1 = 0xffff, id2 = 0xffff
found phy at addres = 2
stmac_phy_get_addr(): id1 = 0x7, id2 = 0xc0f1
stb_id = c0a001a63
Loading Ramdisk to 81d3c000, length 002c35fa ... OK
Starting kernel console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:30:00:0A:00:1A:63 Manufacture=Spark-Project STB_ID=0C:00:0A:00:00:1A:63 - 0x0153d000 - 2897402 ...
Linux version 2.6.32.42_stm24_V4.1 -YW-STM24 0.0.02 v0.1.3 (d26lf@linux-server19) (gcc version 4.5.3 20110525 (STMicroelectronics/Linux Base 4.5.3-79) (GCC) ) #73 PREEMPT Tue Aug 7 17:15:38 CST 2012
Boot params:
... MOUNT_ROOT_RDONLY - 00000001
... RAMDISK_FLAGS - 00000000
... ORIG_ROOT_DEV - 00000200
... LOADER_TYPE - 00000001
... INITRD_START - 0153d000
... INITRD_SIZE - 002c35fa
Booting machvec: hdk7105
Node 0: start_pfn = 0x40000, low = 0x49000
Zone PFN ranges:
Normal 0x00040000 -> 0x00049000
M***ble zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00040000 -> 0x00049000
STMicroelectronics HDK7105 board initialisation
STx7105 version 4.x
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 36576
Kernel command line: console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:30:00:0A:00:1A:63 Manufacture=Spark-Project STB_ID=0C:00:0A:00:00:1A:63
PID hash table entries: 1024 (order: 0, 4096 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
PVR=04909200 CVR=60880000 PRR=00009e40
I-cache : n_ways=2 n_sets=512 way_incr=16384
I-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Memory: 129704k/147456k available (3551k kernel code, 1366k data, 132k init)
Hierarchical RCU implementation.
NR_IRQS:600
Failed to enable clk CLKA_REF, ignoring
Failed to enable clk CLKA_PLL0LS, ignoring
Console: colour dummy device 80x25
console [ttyAS0] enabled
sh_tmu: TMU0 used for clock events
sh_tmu: TMU0 used for periodic clock events
sh_tmu: TMU1 used as clock source
Calibrating delay loop... 532.48 BogoMIPS (lpj=266240)
Mount-cache hash table entries: 512
CPU: STx7105
NET: Registered protocol family 16
Configuring FLASH for boot-from-SPI
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
cfg80211: Calling CRDA to update world regulatory domain
Switching to clocksource TMU1
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Freeing initrd memory: 2829k freed
Slow work thread pool: Starting up
Slow work thread pool: Ready
NTFS driver 2.1.29 [Flags: R/W].
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
ROMFS MTD (C) 2007 Red Hat, Inc.
fuse init (API version 7.13)
JFS: nTxBlock = 1036, nTxLock = 8293
yaffs Jul 18 2012 17:26:24 Installing.
msgmni has been set to 259
alg: No test for stdrng (krng)
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
STMicroelectronics ASC driver initialized
stm-asc.0: ttyAS0 at MMIO 0xfd032000 (irq = 121) is a stm-asc
stm-asc.1: ttyAS1 at MMIO 0xfd033000 (irq = 120) is a stm-asc
brd: module loaded
loop: module loaded
MiPHY3, c1.5 Claimed by sata-stm
scsi0 : sata-stm
ata1: SATA max UDMA/133 irq 72
ata1: SATA link down (SStatus 0 SControl 0)
STMMAC driver:
platform registration...
done!
PMT module supported
DWMAC1000 - user ID: 0x10, Synopsys ID: 0x33
Enhanced descriptor structure
no valid MAC address;please, use ifconfig or nwhwconfig!
eth0 - (dev. name: stmmaceth - id: 0, IRQ #134
IO base addr: 0xfd110000)
STMMAC MII Bus: probed
eth0: PHY ID 0007c0f1 at 2 IRQ 0 (0:02) active
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
CSLIP: code copyright 1989 Regents of the University of California.
SLIP linefill/keepalive option.
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver net1080
usbcore: registered new interface driver zaurus
usbcore: registered new interface driver zd1201
usbcore: registered new interface driver usb8xxx
nwhw_config: (eth0) setting mac address: 30:00:0A:00:1A:63
usbmon: debugfs is not available
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
stm_usb_probe: usb_phy_clk clock not found for stm-usb.0
stm-ehci stm-ehci.0: st-ehci
stm-ehci stm-ehci.0: new USB bus registered, assigned bus number 1
stm-ehci stm-ehci.0: irq 169, io mem 0xfe1ffe00
stm-ehci stm-ehci.0: USB 0.0 started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
[usb_probe_interface]drive name=hub
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
stm-ohci stm-ohci.0: stm-ohci
stm-ohci stm-ohci.0: new USB bus registered, assigned bus number 2
stm-ohci stm-ohci.0: irq 168, io mem 0xfe1ffc00
usb usb2: configuration #1 chosen from 1 choice
[usb_probe_interface]drive name=hub
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
stm_usb_probe: usb_phy_clk clock not found for stm-usb.1
stm-ehci stm-ehci.1: st-ehci
stm-ehci stm-ehci.1: new USB bus registered, assigned bus number 3
stm-ehci stm-ehci.1: irq 143, io mem 0xfeaffe00
stm-ehci stm-ehci.1: USB 0.0 started, EHCI 1.00
usb usb3: configuration #1 chosen from 1 choice
[usb_probe_interface]drive name=hub
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
stm-ohci stm-ohci.1: stm-ohci
stm-ohci stm-ohci.1: new USB bus registered, assigned bus number 4
stm-ohci stm-ohci.1: irq 142, io mem 0xfeaffc00
usb usb4: configuration #1 chosen from 1 choice
[usb_probe_interface]drive name=hub
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
sh_tmu: TMU0 kept as earlytimer
sh_tmu: TMU1 kept as earlytimer
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
STMicroelectronics - Coprocessors st231 Init
st-coprocessor-0: No RAM reserved
st231.0 Coprocessor -------------------------------------------
not configured!
---------------------------------------------------------------
st-coprocessor-1: No RAM reserved
st231.1 Coprocessor -------------------------------------------
not configured!
---------------------------------------------------------------
stm-rng hardware driver 1.0 configured
heartbeat: version 0.1.1 loaded
TCP cubic registered
NET: Registered protocol family 17
lib80211: common routines for IEEE802.11 drivers
NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bit)
stm-nand-flex: Using boot partition name [uboot] (from kernel config)
Creating 7 MTD partitions on "stm-nand-flex.0":
0x000000000000-0x000000100000 : "uboot"
0x000000100000-0x000000b00000 : "Spark kernel"
0x000000b00000-0x000001200000 : "Reserve0"
0x000001200000-0x000001400000 : "Reserve1"
0x000001400000-0x000018000000 : "Spark Userfs"
0x000018000000-0x000018800000 : "E2 kernel"
0x000018800000-0x00001ff00000 : "E2 Userfs"
stm-nand-flex: Found BOOT parition[uboot], updating ECC paramters
boot-ECC 0x00000000->0x00100000
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
RAMDISK: gzip image found at block 0
usb 1-1: new high speed USB device using stm-ehci and address 2
usb 1-1: configuration #1 chosen from 1 choice
[usb_probe_interface]drive name=usb-storage
scsi1 : SCSI emulation for USB Mass Storage devices
VFS: Mounted root (ext2 filesystem) on device 1:0.
Freeing unused kernel memory: 13
starting pid 528, tty '': '/etc/init.d/rcS'
Welcome to STLinux!
waitting for peripheral device mount...ls: /tmp/: No such file or directory
cannot find /etc/network/interface
yaffs: dev is 32505860 name is "mtdblock4"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.4, "mtdblock4"
yaffs: restored from checkpoint
yaffs_read_super: isCheckpointed 1
mount ok
usr scripts
ln: /usr/lib/libfreetype.so: File exists
ln: /usr/lib/libfreetype.so.6: File exists
scsi 1:0:0:0: Direct-Access Kingston DT 100 G2 1.00 PQ: 0 ANSI: 2
sd 1:0:0:0: [sda] 7831552 512-byte logical blocks: (4.00 GB/3.73 GiB)
sd 1:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Assuming drive cache: write through
sda: detected capacity change from 0 to 4009754624
sda: sda1
sd 1:0:0:0: [sda] Assuming drive cache: write through
sd 1:0:0:0: [sda] Attached SCSI rem***ble disk
ln: /usr/lib/libz.so.1: File exists
$Starting sshd:ok
tmp is exist
/root/spark/Ad is exist
sttbx_early_core: module license 'ST Microelectronics' taints kernel.
Disabling lock debugging due to kernel taint
* Looking for chipset model and version...
Load module stos_core [?] by insmod (pid 719)
Load module stsys_ioctl [253] by insmod (pid 721)
STx7105 D detected
* Loading companions
LXLOAD(video1) : LX loaded => Base=0x40000000 - Last=0x40152c24 - Size=1387556
LXLOAD(audio1) : LX loaded => Base=0x40400000 - Last=0x405d0934 - Size=1902900
* Inserting Multicom
ICS init 1 debug_flags 0x40 debug_chan 0x5 connect 0 watchdog 0 bpa2_part 'bigphysarea'
Failed to find BPA2 region 'bigphysarea'
ICS: Failed to find BPA2 partition 'bigphysarea'
ics: probe of ics failed with error -22
insmod ics_user.ko
insmod embx.ko
EMBX init debug_flags 0x0 debug_chan 0x5
insmod embxmailbox.ko
insmod mme.ko
MME module init=1 debug_flags=0x0 pool_size=524288
insmod mme_user.ko
* Inserting STAPI Module
Load module stevt_core [?] by insmod (pid 781)
Load module stcommon_core [?] by insmod (pid 781)
Load module sttbx_core [?] by insmod (pid 781)
Load module stclock_core [251] by insmod (pid 781)
Load module stclkrv_core [?] by insmod (pid 781)
Load module stpower_core [250] by insmod (pid 781)
Load module stfdma_core [249] by insmod (pid 781)
IRQ 205/STFDMA_InterruptHandler: IRQF_DISABLED is not guaranteed on shared IRQs
IRQ 204/STFDMA_InterruptHandler: IRQF_DISABLED is not guaranteed on shared IRQs
Load module stmerge_core [?] by insmod (pid 781)
Load module stavmem_core [?] by insmod (pid 781)
Load module stbuffer_core [?] by insmod (pid 781)
Load module stinject_core [?] by insmod (pid 781)
Load module stpio_core [?] by insmod (pid 781)
Load module stdenc_core [?] by insmod (pid 781)
Load module stlayer_core [?] by insmod (pid 781)
Load module stvout_core [?] by insmod (pid 781)
Load module stvtg_core [?] by insmod (pid 781)
Load module stvid_core [?] by insmod (pid 781)
Load module stvin_core [?] by insmod (pid 781)
Load module stos_core [?] by insmod (pid 781)
Load module stvmix_core [?] by insmod (pid 781)
Load module stgxobj_core [?] by insmod (pid 781)
Load module staudlx_core [247] by insmod (pid 781)
Load module stcc_core [?] by insmod (pid 781)
Load module stttx_core [?] by insmod (pid 781)
Load module stvbi_core [?] by insmod (pid 781)
Load module stblit_core [?] by insmod (pid 781)
Load module stsmart_core [244] by insmod (pid 781)
Load module stnet_core [?] by insmod (pid 781)
Load module stpti4_core [?] by insmod (pid 781)
Tuxera NTFS driver 3012.2.25 [Flags: R/W MODULE].
Load module stfrontend_core [243] by insmod (pid 781)
Load module ywca_module [190] by insmod (pid 781)
Load module smart_module [169] by insmod (pid 781)
Load module stevt_ioctl [242] by insmod (pid 781)
Load module stcommon_ioctl [241] by insmod (pid 781)
Load module sttbx_ioctl [240] by insmod (pid 781)
Load module stclkrv_ioctl [239] by insmod (pid 781)
Load module stpower_ioctl [238] by insmod (pid 781)
Load module stfdma_ioctl [237] by insmod (pid 781)
Load module stmerge_ioctl [235] by insmod (pid 781)
Load module stavmem_ioctl [234] by insmod (pid 781)
Load module stbuffer_ioctl [233] by insmod (pid 781)
Load module stinject_ioctl [232] by insmod (pid 781)
Load module stspi_ioctl [230] by insmod (pid 781)
Load module stpio_ioctl [229] by insmod (pid 781)
Load module stdenc_ioctl [227] by insmod (pid 781)
Load module stlayer_ioctl [226] by insmod (pid 781)
Load module stvout_ioctl [225] by insmod (pid 781)
Load module stvtg_ioctl [224] by insmod (pid 781)
Load module stvid_ioctl [223] by insmod (pid 781)
Load module stvin_ioctl [222] by insmod (pid 781)
Load module stvmix_ioctl [221] by insmod (pid 781)
Load module stgxobj_ioctl [220] by insmod (pid 781)
Load module stcc_ioctl [218] by insmod (pid 781)
Load module stttx_ioctl [217] by insmod (pid 781)
Load module stvbi_ioctl [216] by insmod (pid 781)
Load module stblit_ioctl [215] by insmod (pid 781)
Load module stsys_ioctl [209] by insmod (pid 781)
Load module stnet_ioctl [208] by insmod (pid 781)
Load module stpti4_ioctl [207] by insmod (pid 781)
Load module stfrontend_ioctl [206] by insmod (pid 781)
* Inserting uinput Module
* Creating device nodes in /dev/stapi
make node for /dev/stapi/stfrontend_ioctl 206
make node for /dev/stapi/stpti4_ioctl 207
make node for /dev/stapi/stkeyscn_ioctl 211
make node for /dev/stapi/stnet_ioctl 208
make node for /dev/stapi/stsys_ioctl 209
make node for /dev/stapi/sthdmi_ioctl 210
make node for /dev/stapi/stsmart_ioctl 212
make node for /dev/stapi/stblast_ioctl 213
make node for /dev/stapi/stsubt_ioctl 214
make node for /dev/stapi/stblit_ioctl 215
make node for /dev/stapi/stvbi_ioctl 216
make node for /dev/stapi/stttx_ioctl 217
make node for /dev/stapi/stcc_ioctl 218
make node for /dev/stapi/staudlx_ioctl 219
make node for /dev/stapi/stgxobj_ioctl 220
make node for /dev/stapi/stvmix_ioctl 221
make node for /dev/stapi/stvin_ioctl 222
make node for /dev/stapi/stvid_ioctl 223
make node for /dev/stapi/stvtg_ioctl 224
make node for /dev/stapi/stvout_ioctl 225
make node for /dev/stapi/stlayer_ioctl 226
make node for /dev/stapi/stdenc_ioctl 227
make node for /dev/stapi/stpwm_ioctl 228
make node for /dev/stapi/stpio_ioctl 229
make node for /dev/stapi/stspi_ioctl 230
make node for /dev/stapi/sti2c_ioctl 231
make node for /dev/stapi/stinject_ioctl 232
make node for /dev/stapi/stbuffer_ioctl 233
make node for /dev/stapi/stavmem_ioctl 234
make node for /dev/stapi/stmerge_ioctl 235
make node for /dev/stapi/stfdma_ioctl 237
make node for /dev/stapi/stclkrv_ioctl 239
make node for /dev/stapi/stcommon_ioctl 241
make node for /dev/stapi/stevt_ioctl 242
make node for /dev/stapi/stuart_ioctl 236
make node for /dev/stapi/stpower_ioctl 238
device number is 190
usbcore: registered new interface driver rt73
rtusb init rt5370 --->
usbcore: registered new interface driver rt5370
rtusb init --->
usbcore: registered new interface driver rt2870
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
Open1211 - version Sun Jun 20 06:30:21 CST 2010
usbcore: registered new interface driver zd1211b
_____ ____ _ ____
|__ / _| _ \ / \ / ___|
/ / | | | | | |/ _ \ \___ \
/ /| |_| | |_| / ___ \ ___) |
/____\__, |____/_/ \_\____/
|___/
Open1211 - version Sun Jun 20 06:30:21 CST 2010
usbcore: registered new interface driver zd1211
usbcore: registered new interface driver r871x_usb_drv
rtw driver version=v2.0.1324.20110126
usbcore: registered new interface driver rtw_usb_drv
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2-YW_0.0.3:USB Driver for GSM modems
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
USB Serial support registered for Sierra USB modem
usbcore: registered new interface driver sierra
sierra: v.1.3.8:USB Driver for Sierra Wireless USB modems
Starting inadyn: autotest exist
demod_d0367ter_Identify pucActualID = 0x60
---------Got tuner sharp6465----------!
demod_d0367qam_Identify pucActualID = 0x60
IRQ 220/BLITTER: IRQF_DISABLED is not guaranteed on shared IRQs
input: ywvinput as /devices/virtual/input/input0
input: droidinput as /devices/virtual/input/input1
[ERROR:0x01900001][fuc:YWPVR_Init][line:2162]
[MAIN] YWPVR_Init error,errCode=0x1af0000
ASSERT!! /home/d03ljf/workspace/temp_source/spark_app_ret_duo_A34/src/main/main.c (3576)
[MAIN] YWPRM_Init error,errCode=0x1900004
ASSERT!! /home/d03ljf/workspace/temp_source/spark_app_ret_duo_A34/src/main/main.c (3649)
[MAIN] YWCHANNEL_Init error,errCode=0x1f40001
ASSERT!! /home/d03ljf/workspace/temp_source/spark_app_ret_duo_A34/src/main/main.c (3656)
new dbase
[MAIN] YWEPG_Init error,errCode=0x1f80001
ASSERT!! /home/d03ljf/workspace/temp_source/spark_app_ret_duo_A34/src/main/main.c (3687)
[MAIN] YWTTX_Init error,errCode=0x1f90004
ASSERT!! /home/d03ljf/workspace/temp_source/spark_app_ret_duo_A34/src/main/main.c (3708)
[MAIN] init finish,errCode=0
YWAVOSi_LAYERSetup 0
YWAVOSi_LAYERSetup 2
YWAVOSi_LAYERSetup 3
YWAVOSi_LAYERSetup 4
YWAVOSi_LAYERSetup 6
****cmdline =insmod modules/stgfb_core.ko mod_init=NO g_devnum=1 layer_name=LAYER_GDP1 g_tvOutMode=1280x720-50 g_mem=18 g_format=ARGB8888 g_ratio=16TO9 g_alpha=128 mem_clear=ALL
IRQ 220/STGFB_Blitter: IRQF_DISABLED is not guaranteed on shared IRQs
########################## uiCompSize[0X00AE8BCC]================
*********get viewport handle: 0xc178fa90, 0xc178fa90
OptimizeType = 0
[ERROR][fuc:YWPVR_Open][line:2535] PvrInitParam.bIsInit
[ERROR][fuc:YWPVR_Start][line:3100]
[31;4m[*error*][m[YWPUBLIC_StandbyCheckTimer:3501]
uAutoBootTime(0) curr time 2000-01-01 00:00:10
[31;4m[*error*][m[YWPUBLIC_StandbyCheckTimer:3522]bAutoBootFlag(1),nCurDateTime(0x386d438a),nJmpBootTime(0xffffffff) uAutoBootTime(0x0) nSysBootTime(0xffffffff) nBootTime(0xffffffff) TimerInfo.TimerId(0x0)
save exit: isCheckpointed 1
save exit: isCheckpointed 1
[31;4m[*error*][m[YWPUBLIC_StandbyCheckTimer:3625]
nBootTime(ffffffff) Date 2106-02-07 06:28:15
[31;4m[*error*][m[YWPUBLIC_SysStandBy:3638] YWPUBLIC_StandBy nBootTime ffffffff ErrorType(0x0) YWPUBLIC_GetPowerStatus(0)
[ERROR][YWPANEL_VFDDisplayString]bad parameter
[YWPANELi_Standby] time = ffffffff
OptimizeType = 0
[31;4m[*error*][m[YWSIGNAL_Init:1303]gIntegrateTunerType: 0
HELP,HELP
