Posts by kissem

think i sorted the problem , after initialising the tuner to the required satellites, a full system reboot is required to allow the motor to move , , strange as ive never had this happen on any other box before, hope this helps others as it had me done in all day .

Hi having problems driving my nbox to satellites after installing new image , ive installed nebula zero this morning , followed the onscreen wizard to set box up , ii have configured tuner a to advanced set it up so position 1 is 28 east and position 2 is 0.8 west , allowed diseq 1.2 for both these satellites and gavethem there positions . i have a full working setup as i have retried it in my dm 800 and the motor works fine so that is not a problem . when going into position setup i select position 1 and manually add transponder for this . i have the sat cable from my motor plugged into ant 2 and receive a good signal for this , i proceed tyo scan the position 1 no problem . the channels work fine , i then go back into position setup select position 2 , then tune and manually enter a transponder there . i then try to drive my motor and it will just not move at all , i have reflashed the box with the hyoperion image and followed again as above and still cannot get the motor to move i must be doing somthing wrong , is there somthing i am missing when setting this box up as the above method works great on all other enigma 2 boxes i own , any help would be much appreciated

just installed this image , lookks great , only 1 problem , when i login using dcc , or total commander i cannot access the ftp part , it comes up blank so i cannot insert my lines , this is whats wrote below the ftp section
< 200 PORT command successful. Consider using PASV.
> LIST
< 150 Here comes the directory listing.
< 426 Failure writing network stream.
! RETR/LIST/NLST Failed

login is root
passwd is pkteam
any help would be appreciated thanx

thank you done as you suggested maxhops =2 , working great

the new version of oscam you sent me works , copied the 3 files over , conf, user and server restarted the cam and bang came straight on ,
i have only 1 c-line installed at the moment , would it make any difference if i generated a new oscam.server file with my whole 5x c-lines i have and insert that or would i need to change anything else in the keys folder ?
also installed mgcamd got that working straight away but read on your post ity needs to be oscam to allow recording whilst watching another programme ,

thank you for your help its much appreciated

rebooted box , got gsod continuously ,error was caused by oscam 8599, had to reinstall this time went for nebula v3 , downloaded oscam 3144 stable ,
enabled oscam and entered everything you wrote , i only want to connect to a friends server i dont want to serve , this is what im now getting in oscam server screen thru internet explorer
1335 l 0 root 0 0 127.0.0.1 0 logger 01.01.00 01:20:22 4856d 11:33:06 0000:0000 4856d 11:33:06 OK
1336 h 1 root 0 0 127.0.0.1 0 monitor 01.01.00 01:20:22 4856d 11:33:06 0000:0000 00:00:00 OK
1337 p 2 xxxxxxxx0 0 0.0.0.0 9001 cccam 01.01.00 01:20:22 4856d 11:33:06 0963:0EED 4856d 11:33:06 OFF
1338 c 1 local 0 0 127.0.0.1 0 dvbapi 01.01.00 01:20:22 4856d 11:33:06 0963:0EED not found 4856d 11:33:06 OK

not getting any connection at all , any help would be appreciated
thanx

2000/01/01 1:20:37 1337 p02 configuration error!
2000/01/01 1:20:37 1338 c01 local (0961&000000/0EED/67:40C1): rejected reader peer (3 ms)
2000/01/01 1:20:38 1337 p02 proxy reader: xxxxx(xxxxxxxxxx:9001) cccam v2.1.2 build 3094, maxhop: 10, retry ecm: 1, auto
2000/01/01 1:20:38 1337 p02 configuration error!
2000/01/01 1:20:38 1338 c01 local (0963&000000/0EED/67:40C1): rejected reader peer (4 ms)
2000/01/01 1:20:38 1338 c01 dvbapi: try pids again #1
2000/01/01 1:20:38 1337 p02 proxy reader: xxxxxxx(xxxxxxx:9001) cccam v2.1.2 build 3094, maxhop: 10, retry ecm: 1, auto
2000/01/01 1:20:38 1337 p02 configuration error!

well i must admit this has got me totally beat ,
been using dm 800s for years never had any problems like this +
ive followed the above to the letter , installed oscam 8599 chmoded the attributes , edited the oscam conf ,( changed http port to 8080)
, oscam.server and the oscam.user
to be the same as above , i get absolutley nothing , i cannot see anywhere where the server port number goes ianywhere in the oscam file above ,
any help would be appreciated ,. here are my 3 folders found in var keys (ive edited out my server id , username and password )

oscam.conf
[global]
logfile = /tmp/oscam.log
clienttimeout = 1600
fallbacktimeout = 1500
clientmaxidle = 300
netprio = 1
unlockparental = 1
nice = -1
maxlogsize = 1000
waitforcards = 0
waitforcards_extra_delay = 400
preferlocalcards = 1
dropdups = 1
cacheexwaittime = 60
usrfile = /tmp/oscam/oscamuser.log
cwlogdir = /tmp/oscam/cw
emmlogdir = /tmp/oscam/emm.log

[dvbapi]
enabled = 1
au = 1
boxtype = dreambox
user = local

[webif]
httpport = 8080
httpuser = root
httppwd = pkteam
httprefresh = 0
httpallowed = 127.0.0.1,192.168.1.1-192.168.1.255
httphideidleclients = 0
httpreadonly = 0

oscam.server
[reader]
protocol = cccam
device = xxxxx.is-xxx.com
user = xxxxxx
password = xxxxxx
inactivitytimeout = 30
group = 1
cccversion = 2.3.0
cccmaxhops = 3
ccckeepalive = 1
cccreshare = 0

oscam.user

[account]
user = local
group = 1
cccstealth