Posts by mintosh72

37d584cfb7685e.png

72fbe92ad.jpg

thats what i mean

hi there

im on openatv 6.1

all working good

how do i get the top picks to show in channel list and also in the tv guide like on the whooshbuild ??

thanks mintosh72

tryed that didnt work!!!!

hi there
i have a vu solo running on openpli 4
and have epg import installed
but when trying to download epg i get 0 events
i have rytec uk xmltv ticked sources
but still get nothing?????

hi there
i have installed the latest version of this plugin on a vu duo2 openpli 4
but the sportsdevil plugin is not there
in the sports section of addons??????????????

hi there
thanks for all your replies
i have now got it working but cant download from opentv providers 28.2
it works with xepgdb but a few channels are blank asian ones
my vu duo 2 on openpli 4.0 works fine with opentv
could really do with opentv providers working
any ideas anyone?????????
thanks mintosh72

sorry guys getting a bit confused here

open telnet session type

opkg update/cut/ hit return and type

opkg install libcurl4

or type opkg update /cut/

and then install the file via software mangement
sorry
thanks mintosh72

hi there
i have a vu duo running on openpli 4.0 and cant get the epg to download
i have ftp the ibcurl4_7.35.0-r0.1_mips32el.ipk to the TMP folder
then go to software mangement in pluginns
install local extension
memory/tmp
it shows installing file
but still no epg????
thanks mintosh72

hi there
i have a vu duo running on openpli 4.0
i want to make a full backup of my system and settings to usb
so i can flash my friends box in 1 step without having to add all the extras
and also to post backup on forum
dont know what plugin to use and how
thanks mintosh72

hi there
thanks for all your answers
i have tryed to reflash the box but no joy i have tryed 2 usb sticks both formated
i tryed flashing when in enigma mode no joy after a hour
ive switched to spark and try the e2upgrade plugin and get the the message cant find kennel file
then back in enigma mode i ftp the oscam file by nano in post 2 to the tmp file
then in via menu pkt blue panel install /gz
it reads it loads of writing comes up but when in emu menu it doesnt show even after restart enigma
the file is ftp over unziped is that right?
if not when unzipped your left with 3 files what goes where?????
i really dont get this ive done a alien2 same image different oscam (oscam_ymod) i had no problems
any ideas anyone???????
ONCE AGAIN ID LIKE TO SAY THANKYOU TO EVERYONE WHO AS ANSWERED
Thanks mintosh72

hi there
i have a amiko alien 8900 on the Lavatronics-PKT-Backup-FEB2014
im trying to use oscam
i ftp the oscam server file to var/keys
and it looks like this

[reader]
label = Name1
enable = 1
protocol = newcamd
device = exapmle.co.uk,10000
key = 0102030405060708091011121314
user = username
password = password
reconnecttimeout = 8298808
fix9993 = 0
group = 4
lb_weight = 100

it connects i see the sever in emu
but nothing clears
PLEASE CAN SOMEONE HELP ME
THANKS MINTOSH72

hi there
i have tryed what dacpep suggested in post 15
but still no joy its driving me nuts
i know my line is good tested on another box connecting fine
i also done a amiko alien 2 for friend yesterday and that works fine using oscam????
i just dont know where im going wrong
can anyone help me PLEASE!!!!
thanks mintosh72

hi there im using this image on my alien 8900
but having problems with the oscam
i ftp my osacam sever file to var/keys
the oscam sever file looks like this

############### General Instruction - oscam.server ###################
# To activate/deactivate the reader set enable = 1/0 #
# #
# You might specify further entries in each reader section #
# such as "caid =________" and/or "services = _________" but you needn´t #
# For further details see the OSCAM documentation #
############################################################################

######################### Internal Readers ###############################
# Default Config should work with Seca, Conax, Cryptoworks, Viaccess, NDS #
# #
# For I*****, Betacrypt just activate "cardmhz=600" by removing the "#" #
# #
# For Nagra activate and set the correct "rsakey = " and "boxkey = " en #
# examples for *** UK are included #
# #
# for specific Smartcards such as TIGER or Viaccess with AES-Key #
# see the OSCAM documentation #
############################################################################

[reader]
label = ***UK
protocol = internal
device = /dev/sci0
blockemm-u = 0
blockemm-s = 0
blockemm-g = 1
blockemm-unknown = 1
emmcache = 1,3,2
group = 1
caid = 0963

[reader]
label = ***UK
protocol = internal
device = /dev/sci1
blockemm-u = 0
blockemm-s = 0
blockemm-g = 1
blockemm-unknown = 1
emmcache = 1,3,2
group = 1
caid = 0963

#################### External Readers / SMARGO ########################
# Important !!!! Use SMARGO Firmware 1.4 or 1.5 #
# With regard to your Smartcard set up the Reader/Smargo as follows: #
# #
# For Seca, Conax, Cryptoworks, Viaccess, NDS, Nagra #
# Frequency Fixed 3,69 Mhz / Normal / T=0 / EGT = 0 #
# #
# For I*****, Betacrypt #
# Frequency Fixed 6,0Mhz / Normal / T=1 / EGT = 0 #
# #
# If SMARGO ist in Autoswitch mode, than activate fitting mhz/cardmhz- #
# Entries in the reader-Section #
# # #
# For Nagra activate and complete the "rsakey = " and "boxkey = " and #
# and remove the # in the smargopatch = 1 line #
# example for HDplus is included #
# #
# for specific Smartcards such as TIGER or Viaccess with AES-Key #
# see the OSCAM documentation #
############################################################################

[reader]
enable = 0
description = Set as HD plus HD02
label = Extern_0
protocol = mouse
device = /dev/ttyUSB0
emmcache = 1,1,2
detect = CD
group = 1
smargopatch = 1
caid = 1843
rsakey = BF358B5461863130686FC933FB541FFCED682F3680F09DBC1A23829FB3B2F766B9DD1BF3B3ECC9AD6661B753DCC3A9624156F9EB64E8168EF09E4D9C5CCA4DD5
boxkey = A7642F57BC96D37C
#mhz = 357
#cardmhz = 357

[reader]
enable = 0
description = Set as *** S02
label = Extern_1
protocol = mouse
device = /dev/ttyUSB1
emmcache = 1,1,2
detect = CD
group = 1
caid = 1702
#mhz = 600
#cardmhz = 600

######################### Remote Readers ##############################
# Important !!!! Use this or not in personal responsibility #
# #
# #
# For further details see the OSCAM documentation #
############################################################################

[reader]
label = remote
description = Newcamd Example
protocol = newcamd
device = sever address,port
key = 0102030405060708091011121314
user = username
password = password
caid = 0963
ident = 0000:000000
group = 1
audisabled = 1

[reader]
label = remote
description = CCcam Example
reconnecttimeout = 5
protocol = cccam
device = example.server.com,12000
user = username
password = password
group = 1
blockemm-u = 1
blockemm-s = 1
blockemm-g = 1
blockemm-unknown = 1
caid =
cccversion = 2.1.4

######## end of file ########

i dont know what im doing wrong???
i have used this file on amiko alien2
and it works
thanks mintosh72

Thankyou thankyou thankyou
mgcamd is working now!!!!!!!!

hi there
i am using mgcamd 1.35
the format for the newcamd file

CWS_KEEPALIVE=60
CWS=SERVER,USER,PASS,0102030405060708091011121314 Ian server1

hi there
im trying to use mgcamd on my vu duo2
i ftp my newcamd.list file to usr/keys
but nothing clears i know my server is active i can use the ccam version plus other boxes in house are clearing
i used the same mg_cfg as the one i used on vu duo
just dont know why i cant get it to work??????

hi there
i have a vu duo2 running on openpli 4.0
will the linuxsupport -addons plugin work?
if so which one do i download and use????
thanks mintosh72