Connecting one dm800se Box to another Dm800se When only using Oscam and Dvbapi

Hi there

Im sure this has probsbly been asked before. i have searched but unable to find a clear answer so please forgive me for asking

Was hoping someone could please advise me as i am sort of confused.

Usually when using Oscam with CCCam i would normally connect to the dreambox via N line or newcamd line from another dreambox

If i was using mgcamd i would connect with a CWS line

The issue i am facing right now is if i am clearing pics using just oscam in dreambox 800se and dvapi how would i connect the other box.

i would be so grateful if someone could please advise me by an example

thanking you in advance for any advice

I didn't mean as pay server. I meant in my home network to connect to my other box

Is there a specific setting in the oscam config or in cccam.cfg or newcamd.list I have to put the dreambox which gas oscam in order for my other box to connect whether Sam using cccam or mgcamd or must other box have oscam to connect other box which is only using oscam with dvbapi. Is there an example of settings I can use

when I get home in an hour I will post my configs. If anyone could please check them and advise me where I am going wrong or if I am missing something

here are my posts if anyone can help me please

##oscam.conf

[global]

logfile = /dev/tty

clienttimeout = 4000

clientmaxidle = 300

netprio = 1

nice = -1

maxlogsize = 1000

waitforcards = 0

preferlocalcards = 1

dropdups = 1

[streamrelay]

stream_relay_enabled = 0

[dvbapi]

enabled = 1

au = 1

pmt_mode = 0

delayer = 60

user = dvbapi

read_sdt = 1

extended_cw_api = 2

boxtype = dreambox

[newcamd]

port = 1234@0604:000000

key = 0102030405060708091011121314

mgclient = 1

keepalive = 1

[webif]

httpport = 8888

httpuser = XXXXXXXX

httppwd = XXXXXXXX

httprefresh = 10

httppollrefresh = 10

httpallowed = 127.0.0.1,0.0.0.0-255.255.255.255

http_status_log = 1

##oscam.server

[reader]

label = emulator

enable = 0

protocol = emu

device = emulator

caid = 0604

detect = cd

ident = 0604:000000

group = 1

emmcache = 2,1,2,1

emu_auproviders = 0604:000000

[reader]

label = card

protocol = internal

device = /dev/sci0

caid = 0604

detect = cd

mhz = 540

cardmhz = 2700

ident = 0604:000000

group = 2

blockemm-unknown = 1

[reader]

label = card1

enable = 0

protocol = internal

device = /dev/sci1

caid = 0604

detect = cd

mhz = 600

cardmhz = 2700

ident = 0604:000000

group = 3

blockemm-unknown = 1


##oscam.user

[account]

description = dvbapi

user = dvbapi

monlevel = 4

au = 1

group = 1,2,3

[account]

user = test

pwd = test

monlevel = 4

group = 2

##CCCam.cfg

Its blank (empty file)

##Newcamd.list

Its blank (empty file)

its just got these 4 default lines

CWS_KEEPALIVE = 300

CWS_INCOMING_PORT = 21000

CWS = 192.168.1.1 20000 dummy dummy 10 02 13 04 15 06 17 08 01 10 11 12 13 14 lan server1

CWS_MULTIPLE = 192.168.1.2 20000:20005 dummy dummy 10 02 13 04 15 06 17 08 01 10 11 12 13 14 lan server2

##mg_cfg

# EMM messages

# 00 don't show any EMMs (default)

# 01 show only valid EMMs

# 02 show valid and bad EMMs with complete data display

M: { 01 }

# ECM messages

# 00 don't show anything about ecm

# 01 normal mode, show pids processed, decoded ecm and cw

# 02 verbose mode, show valid and bad ECMs with data

C: { 01 }

# AU

# 00 disable, no emm pids processed

# 01 enable, emm pids always processed for soft-au and shared cards

# 02 auto, emm started only if channel cant be decoded

# 03 process emm pids for network cards update only

A: { 02 }

# key update (sum 01 or 02 with 04)

# 01 update only new keys, default setting

# 02 update all keys (used for valid PMK checking)

# 04 enable TPS au

# + tps SID, which pmt pid contains au pid

U: { 01 } 0x12c0

# config files folder (softcam, autoroll, ignore/priority)

# 00 files in /var/keys

# 01 files in /tmp

T: { 00 }

# network mode, use summ for several clients

# 00 no network (default)

# 01 newcamd netclient

# 02 radegast netclient

# 04 camd3 netclient

# 08 gbox netclient

G: { 01 }

# network retry, use summ for several options

# 00 disable

# 01 retry every new ecm

# 02 try to connect to offline shares every Q: seconds

# 04 try to detect and fast reconnect to lost (and not used atm) server

# + XX messages number and YY seconds to reconnect

# mg will reconnect to server, if no answer to last XX ecm/keepalive or

# if no answer for last ecm or keepalive sent for YY seconds

# set to 0 to disable

N: { 07 } 5 30

# network ecm timeout in seconds

K: { 05 }

# newcamd dead routes connect retry, sec

Q: { 600 }

# network shares priority

# 00 gbox, newcamd, radegast, camd3 (default)

# 01 camd3, radegast, newcamd, gbox

# 02 newcamd, camd3, gbox, radegast

P: { 00 }

# on screen display type

# 00 No OSD (default)

# 01 neutrino

# 02 enigma

# 03 relook

# + user password for http auth

O: { 00 } username password

# on screen display Options, summ of:

# 01 show emu ecm

# 02 show network shares messages

# 04 show decoding failed / fta

# 08 show emm keys update

# + web port to use for osd

S: { 03 } 80

# Log option, summ of:

# 00 off

# 01 network udp log

# 02 log to console

# 04 file, appended ! delete it by yourself, before it eat all your hdd

# + IP udp-port log-file-name

L: { 03 } 172.16.1.1 28007 /tmp/mgcamd.log

# keep ecm cache, seconds

# every cache entry takes 28 bytes, so 24h cache will take *only* 240-400kb of memory,

# for openbox/elanvision users with remote shares make sense to set it higher than default value,

# to not hammer cards while timeshifting or playing crypted recordings.

E: { 15 }

# cache option, summ of:

# 00 Off (default)

# 01 Ecm pids cache, store pids used to decode in /tmp/ca_cache.list at exit, load at startup, same syntax as restore.list

# 02 Ecm data cache, remember CW for (E:) time

# 04 Emm cache for network cards, do not resend the same emm twice, cache not cleared until restart

H: { 07 }

# reread files, summ of:

# 00 No (default)

# 01 reread config file on channel change (including priority and ignore, but not replace/cache)

# 02 reread SoftCam.Key on channel change

# 04 reread SoftCam.Key if file changed

R: { 00 }

# debug, summ of

# 00 off (default)

# 01 debug ecm

# 02 debug emm

# 04 debug network ecm

# 08 debug network emm

# 16 debug network login

# 32 show mem/cpu stats every 1 min

# 64 add timestamp to log messages

D: { 00 }

# box type

# 00 autodetect, change only if you think wrong type detected.

# 01 dbox2

# 02 dreambox

# 03 triple-dragon

# 04 relook

# 05 openbox

B: { 00 }

Additional Dreambox which i wish to connect with

no configs have been done with cccam or mgcamd as am not sure how to connect to the msin dreambox

The only thing that is running is oscam with dvapi. Ideally what i would like to do is connect it via mgcamd if possible and if so what am i missing please unless i can connect to the box as is currently configure but from what i have been reading mgcamd is a better way if i am not mistaken

please advice me if possible

thanking you in advance once again

thankyou so much.

last question i think i need to know is

in the clientbox which softcam do i connect with cccam or mgcamd

and

in the serverbox do i have to enable any softcam such as cccam or mgcamd and also do i have to edit newcand.list or cccam.cfg

thanks again

I tried the above settings and cleared pics on other box also but 10 mins later everything stopped.

I'm not sure where I have gone wrong

Could you please tell me if I have to put anything in cccam.cfg.or newcamd.list or cccam.list and do I have to remove anything from oscam.conf as I am only using card and not the emu component and also which softcam would I connect with from the client box. Is it cccam with nline or mgcamd with cws or something else

All I need is a set of working oscam configs and mgcmd config using a dreambox 800se reading the card from /dev/sc0 and what do to place in oscam.conf file. Example do I need newcamd in there or just cccam and also how to put sid list and where to place it so mgcamd can read it also do I use mine or cws line

i only have oscam in one box so do i also have to install it in secind one also ??

I thought one box has oscam and the seond one connects via nline (cccam or mgcamd)

i'm sorry but i am very confused now

Okay here are my configs

First Box Which has Oscam in it

##oscam.conf##

[global]

logfile = /dev/tty

clienttimeout = 4000

clientmaxidle = 300

netprio = 1

nice = -1

maxlogsize = 1000

waitforcards = 0

preferlocalcards = 1

dropdups = 1

[cache]

[newcamd]

port = 1002@0604:000000

key = 0102030405060708091011121314

keepalive = 1

mgclient = 1

[cccam]

port = 15020

serverip = 192.168.0.127

nodeid = 31DFF96610CB157E

version = 2.2.1

reshare = 1

updateinterval = 30

[streamrelay]

stream_relay_enabled = 0

[dvbapi]

enabled = 1

au = 1

pmt_mode = 0

delayer = 60

user = dvbapi

read_sdt = 1

extended_cw_api = 2

boxtype = dreambox

[webif]

httpport = XXXXXX

httpuser = XXXXXX

httppwd = XXXXXX

httprefresh = 10

httppollrefresh = 10

httpallowed = 127.0.0.1,0.0.0.0-255.255.255.255

http_status_log = 1

##oscam.user##

[account]

user = dvbapi

description = dvbapi

monlevel = 4

au = 1

group = 1,2,3,4

[account]

user = room1

pwd = room1

monlevel = 4

group = 2

##oscam.server##

[reader]

label = emulator

enable = 0

protocol = emu

device = emulator

caid = 0604

detect = cd

ident = 0604:000000

group = 1

emmcache = 2,1,2,1

emu_auproviders = 0604:000000

[reader]

label = card

protocol = internal

device = /dev/sci0

caid = 0604

detect = cd

mhz = 540

cardmhz = 2700

ident = 0604:000000

group = 2

##cccam.cfg##

N: 127.0.0.1 1002 dvbapi 01 02 03 04 05 06 07 08 09 10 11 12 13 14

##newcamd.list##

CWS_KEEPALIVE = 300

CWS_INCOMING_PORT = 21000

CWS = 127.0.0.1 1002 dvbapi 01 02 03 04 05 06 07 08 09 10 11 12 13 14

and in the second box

i have tried the following in cccam.cfg

N: 192.168.0.127 1002 room1 room1 01 02 03 04 05 06 07 08 09 10 11 12 13 14

and i for mgcamd i have tried

CWS = 192.168.0.127 1002 room1 room1 01 02 03 04 05 06 07 08 09 10 11 12 13 14

** both times with both settings it only lasts for around 10 mins then everything freezes **

however if i disable the other box and leave only the main dreambox only with the dvapi it stays on without freezing

this is why i am confused

If you could please see these settings and adjust them for me i would appreciate it as i keep stuffing it up somehow because i do not beleive i need everything i have in there like emulator and the stream relay stuff unless i am wrong .

Sorry if i am sounding stupid but i am really confused here

p.s. i also tried connecting my ultraplus x9200hd just in case it was my second dreambox and i connected the ultraplus using xcamclient with the following line and same results 10 mins then it all freeezes again

the line i used in ultraplus insead of the second dreambox just as a test is

newcamd:192.168.0.127:1002:0/0604/0:room1:room1:0102030405060708091011121314

i have tried your method also amd i think i have found the problem . when it errors on oscam the message i get is

2018/05/21 13:33:59 7099094B c (ecm) dvbapi (0604@000000/0013/000F/44:3B1425DD60414EDE72865CD5D60E0EA9): rejected (209 ms) by card - Alpha Sat (Invalid ecm type for card)

is there a fix for this

does dvbapi need a line in cccam.cfg on dreambox or in newcamd.list as i have nothing in there