Problem with CCcam 2.3.2 on UNO 4k Running BlackHole 3.0.5

There are 10 replies in this Thread which was already clicked 2,742 times. The last Post () by macho.

  • Hi

    I'm a new user

    lately I have bought Uno 4K se and flashed blackhole image 3.0.5 on it and every thing's OK.

    I have downloaded vuplus-team.com_OscamPowervu-11401-CCcam-2.3.2-BlackHole_all.ipk from here and install it on receiver.


    I have downloaded needed files as CCCam.cfg, CCCam.Channelinfo, CCCam.prio & CCCam.providers from here and configured CCCam.cfg files like bellow. (I'm using 5 lines CCCam)


    C: speedman1.zaptoo.pw 40000 ***** *****

    C: speedman2.zaptoo.pw 50000 ***** *****

    C: mega-cccam2.zaptoo.pw 15002 ***** *****

    C: mega-cccam3.zaptoo.pw 18000 ***** *****

    C: sky.zaptoo.pw 11000 ***** *****


    (I Have entered my user name and password instead ***)

    Just this and nothing more is aded to CCCam.cfg file, I have saved it and ftp them (all CCCam.cfg, CCCam.Channelinfo, CCCam.prio & CCCam.providers files) to the receiver.


    after going to desired channel and running the CCCam 2.3.2, a message is shown and the CCCam is started.


    But, it seems that it's not working, cause no scrambled channel is shown.


    Did I do any thing wrong????

    Did I configure the CCCam.cfg file?

    What do I have to do???


    Please help me.

  • ok so normally in Oscam server u should have on reader ccam look like this



    [reader]

    label = remote_cccam or CCcam

    protocol = cccam

    device = the host for c l,the portxxxxxxx

    user = userxxxxxxxxx

    password = passwordxxxxxxxx

    inactivitytimeout = 30

    group = 2

    emmcache = 1,3,2,0

    blockemm-unknown = 1

    blockemm-u = 1

    blockemm-s = 1

    blockemm-g = 1

    cccversion = 2.0.11

    cccmaxhops = 2

  • Hi

    I'm a beginner

    As you said, I tried to use oscam on mu receiver VU+ UNO 4k se

    I have installed enigma2-plugin-softcams-oscam-11392_blackhole_armv7ahf-vfp-neon.ipk on my receiver.

    I converted my Clines to oscam using CCCam to oscam 1.2 converter and paste the new lines to oscam.server on my receiver (etc/tuxbox/config).


    This is the result....

    [reader]

    label=speedman1.zaptoo.pw

    enable=1

    protocol=cccam

    device=speedman1.zaptoo.pw,40000

    user= my username

    password=my pass

    cccversion=2.1.2

    group=1

    inactivitytimeout=1

    reconnecttimeout=30

    lb_weight=100

    cccmaxhops=10

    ccckeepalive=1

    cccwantemu=0


    I also copied 2 files (oscam.conf and oscam.user) to my receiver in the same adress that are attached.


    I start the oscam and try to see a scrambled channel.


    But, it seems that it's not working. nothing happened.


    did I do any thing wrong????


    Please help me.

CCcam Support Forum

Configs, discussion, downloads and guides for CCcam Softcam.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!