Openpli 7.1 for Amiko Alien 5 to test
https://mega.nz/#!kTAkXAwb!Zkm…JZkvH49gtot7SCAicAlfVss-w
Please give feedback to fix issues
Emo
There are 13 replies in this Thread which was already clicked 3,558 times. The last Post () by motelodico72.
Openpli 7.1 for Amiko Alien 5 to test
https://mega.nz/#!kTAkXAwb!Zkm…JZkvH49gtot7SCAicAlfVss-w
Please give feedback to fix issues
Emo
STi7111...?
STi7111...?
No. Amlogic S905D.
Hello, emosim.
First of all, I apologize for my bad English, I use help from an online translator!
I tested this image "Openpli 7.1 for Amiko Alien 5 to test" and came across some problems.
After installing and using a LG 4k TV, I could not see any image on the TV screen, so I turned to OpenWebif to change the resolution and had to change the skin to hd1 or hd2 so that the image would be displayed correctly.
This is the smallest of problems, because I solved it quickly.
Another problem is the network setup, although I don't need to use the wirless setup, there may be those who do.
I leave here comparison images between this PLI and openATV 6.2 in the network configuration:
The biggest problem that no longer allows you to use this image on the receiver is when we try to access any channel in the channel list, the box locks up and we are forced to turn off the power.
Maybe it has to do with tuner's, because the box doesn't update the date and time, as we can see in the following image:
This was my test and as I could see, it was not possible to move on, because without a tuner working well.
ps: I got OSCam working and apparently fine, although only with images can I prove it.
It would be great to have this image working well.
Thank you.
Thank you VERY MUCH for your testing, we are compiling blind the image for Alien5 as we have no box and that would help. Your description is for sure very helpful and we will continue work on it, thank you.
Emo
Can you do a screenshot of the Tuner section in the menu to see how it is recognized ?
Thank you,
Emo
I don't know if these images are enough, if you need others, do not hesitate to ask.
I use here at home 3 sat (Hispasat 30w, Astra 19.2E and Hotbird 13E) with DiSEqC 1.0 A/B/C/D (works great with other images: openATV, openSPA and Pure2), however, in these images, I have only set up Hispasat for testing, yet it fails with any kind of satellite configuration, simple, DiSEqC , etc...
If you click to scan channels, the box locks and only by disconnecting from the mains do we have access to it again, just as when we send a list of channels to the box, with the satellites we have previously configured in the tuner section, if click to see any channel in the list, "the box locks and only by disconnecting from the mains of we have access to it"
Thank you.
Edit:
I leave screens of the openATV image if you need to compare Tuner setup menus:
Very nice thank you, please from the openpli go on the information page (where there is the version of pithon gstreamer etc) and post here the screenshot. I would like to check something.
About the IPTV FTA channels, how it goes ? Do yoo see the stream or does it lock also ? Use the pre installed japhar list.
Thank you !
Emo
Image info:
IPTV:
The box does not block, but I can not see any streams (channel IPTV) and tested a lot of them:
Thank you very much
Emo
Hi, ich habe es drauf gemacht, nur ich kann kein Sendersuchlauf machen, der nur eine Kreisbewegung macht, kann mir einen Tipp geben, was ich machen muss, damit es mal besse3 wird
Die sehr geehrten Kollegen,
Gestern hat das Image Openpli 7 für Alien 5, Mich prosmatriaju die Satellitenkanäle auf vier Gefährten Astra 4,8 und 19 JE, Hot Bird 13 festgestellt,
Eutelsat 36. Leider, nach der Abstimmung des Tuners A, die Suche der Kanäle nicht ausgeführt zu werden.
there is a more recent and stable version of OpenPli for Amiko A5 combo 4k or not?
emosim or nozorrog there is any good news?
I'm running OpenAtv 6.2 normally but it't too old for todays plugin.
I just installed today over a new microsd for testing purpose and I got mismatch of screen resolution on old full hd tv made on 2009.
I see only a quater [top left] of screen. How is possible to change it on OpenWebIf to hd1 or hd2? How do it?
I overcome this problem changing the skin.
I changed the root password.
Now the problem is on the manual search or automatic search of channel at 13East (Hot bird). The receiver lock and I need to restart with a power off.
I'm not able to see tv channel even if they are FTA.
Don’t have an account yet? Register yourself now and be a part of our community!