hi I need working mgcamd for arm I have tried many mgcamd but its not working my old box was mips it worked fine on it I have tried open vix pil open atv but nothing worked I used to put cline in cccamd.list but its not working anymore
Mgcamd for vu+zero 4k
- viper619
- Thread is marked as Resolved.
There are 6 replies in this Thread which was already clicked 2,331 times. The last Post () by johndeere88.
-
-
oscam friend, oscam. uses oscam.
-
oscam friend, oscam. uses oscam.
Oscam channel open slow
-
i need a new gearbox for my car
if you can guess what car it is
i'll show you mgcamd for your image that you dont say
as i know not all gearboxes fits all cars think about it
-
oscam works fine with 4k recievers, very fast change aswell.
Post your cfg;s for oscam
-
[global]
disablelog = 1
disableuserfile = 1
usrfileflag = 0
maxlogsize = 10
preferlocalcards = 1
saveinithistory = 1
lb_mode = 0
unlock_parental = 1
[cs378x]
port = 12005
[webif]
### SET PASSWORD!
httpport = 16001
#httpuser = oscam
#httppwd = oscam
httprefresh = 20
httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255
#httphideidleclients = 1
#httpreadonly = 0
#httpsavefullcfg = 0
#[newcamd]
#port = 35000@0100:000068;35001@0B01:000000
#allowed = 0.0.0.0-255.255.255.255
#key = 0102030405060708091011121314
#keepalive = 1
#mgclient = 1
[dvbapi]
enabled = 1
user = dvbapi
### Please experiment with different pmt=mode values (0-6)
pmt_mode = 4
extended_cw_api = 2
au = 1
### Please experiment with different delayer values (slower boxes may need a bigger value than 60 or 70 milli seconds)
delayer = 70
[streamrelay]
### enable for STBs that need stream relay!
stream_relay_enabled = 0
-
Do you really need dvbapi ? i dont use it on my 4k reciever and oscam emu works fine.
version
- OSCam r11532-797 on my tm twin 4k.
You could try to disable dvbapi and use a line like below into oscam.server file.
edit, actually you will need dvbapi, got confused as webif stated no files for dvbapi.. to that end add this to your cfg from the good admin at linuxsat
[dvbapi]
enabled = 1
au = 1
pmt_mode = 0
request_mode = 1
user = linuxsatsupport
read_sdt = 1
write_sdt_prov = 1
boxtype = dreambox
[reader]
label = line_cccam
protocol = cccam
enable = 1
device = 192.168.1.22,port
user = HOME2
password = HOME2
inactivitytimeout = 30
cacheex_allow_filter = 0
group = 1
[reader]
label = line_newcamd
protocol = newcamd
enable = 1
device = 192.168.1.22,port
key = 0102030405060708091011121314
user = HOME2
password = HOME2
inactivitytimeout = 30
cacheex_allow_filter = 0
group = 1
MGCamd Support Forum
Configs, discussion, downloads and guides for MGCamd Softcam.
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!