1861 Polsat card reports wrong ATR in oscam

There are 6 replies in this Thread which was already clicked 3,420 times. The last Post () by tomek6680.

    Hi Everyone,


    I'm using Vu+ Zero with OpenPli 7.1 and Oscam r11539.
    Couple of days ago my Polsat card with CAID 1861 stopped decoding.

    Oscam logs contain very-very weird info:


    2019/10/24 16:51:07 00000000 s (reader) polsat [internal] creating thread for device /dev/sci0

    2019/10/24 16:51:07 00000000 s (main) waiting for local card init

    2019/10/24 16:51:07 29D27484 r (reader) polsat [internal] Reader initialized (device=/dev/sci0, detect=cd, pll max=27.00 MHz, wanted mhz=4.50 MHz)

    2019/10/24 16:51:07 29D27484 r (reader) polsat [internal] Reader sci internal, detected box type: vuzero

    2019/10/24 16:51:07 697FE1F4 h (webif) webif: decompressed 170944 bytes back into 418544 bytes

    2019/10/24 16:51:07 697FE1F4 h (webif) HTTP Server running. ip=:: port=8081

    2019/10/24 16:51:08 29D27484 r (reader) polsat [internal] card detected

    2019/10/24 16:51:08 29D27484 r (reader) polsat [internal] ATR: 3F FF 95 00 FF 91 81 71 A0 47 00 44 4E 41 53 50 31 39 30 20 4D 65 72 51 32 35 4F

    2019/10/24 16:51:12 29D27484 r (reader) polsat [internal] detected nagra merlin card in legacy mode -> try switch nagra layer to CAK7

    2019/10/24 16:51:12 29D27484 r (reader) polsat [internal] switch nagra layer OK

    2019/10/24 16:51:13 29D27484 r (reader) polsat [internal] Nagra layer ATR: 3F FF 95 00 FF 91 81 71 FE 57 00 44 4E 41 53 50 34 31 30 20 52 65 76 51 32 35 17

    2019/10/24 16:51:18 29D27484 r (reader) polsat [internal] Rom revision: DNASP410 RevQ25

    2019/10/24 16:51:18 29D27484 r (reader) polsat [internal] ERROR: Not all required parameters are set!

    2019/10/24 16:51:18 29D27484 r (reader) polsat [internal] card system not supported

    2019/10/24 16:51:18 29D27484 r (reader) polsat [internal] Normal mode failed, reverting to Deprecated Mode

    2019/10/24 16:51:18 29D27484 r (reader) polsat [internal] THIS WAS A FAILED START ATTEMPT No 1 out of max allotted of 1

    2019/10/24 16:51:18 29D27484 r (reader) polsat [internal] card initializing error


    Here's reader configuration from oscam.server


    [reader]

    label = polsat

    protocol = internal

    device = /dev/sci0

    services = cyfrowy polsat (1861)

    boxkey = someboxkey

    rsakey = somersakey

    detect = cd

    mhz = 450

    cardmhz = 2700

    ident = 1861:000000,007001,007101

    group = 1

    emmcache = 1,3,15,0

    ratelimitecm = 4

    ecmunique = 1

    ratelimittime = 10000

    srvidholdtime = 2000

    cooldown = 30,600



    Does anyone have any ideas how 1861 Polsat card became 1860 HD+ HD02 and is there any way to fix it?

    Thanks in advance.

    No idea and not heard anything, could be CAK7 pairing where new info is required and hard to find, hopefully its something silly so the first thing i would try is the latest oscam you can find and then open a support ticket on oscam streamboard if latest oscam version does not help.


    If you are saying caids are changing i assume you mean in the stream? and not the card itself, i dont know much about polsat but being encrypted with nagravision they may be changing to cardless encryption, and i suppose one way to test that theory is to plug your official polsat reciever in and see if channels clear without a viewing card present,, thats assuming you have a paired official box with your card which most probably wont have.


    If you have a polsat CAM i would try your card in that if you have a box with a module interface that is, vu zero gen 1 obviously does not.


    Add (caid = 1861) to your reader config too, not saying this is your issue tho.

    NAGRA / CAK7 are however paired cards. You should also use the appropriate pairing keys.


    Try updating Oscam yet. The current version is 11572. You can try to update the Oscam with the OpenPLi package manager or use update from the PLUGIN-manager in the GUI MENU. The new Oscam is available directly on the OpenPLi-7 feed server. There are several ways to do so. If you installed your original Oscam from the feed server, just update it. If you installed it as a third-party package, then uninstall your Oscam and install the Oscam from OpenPLi-7 feed server.

    Code
    opkg update               # update the list of available packages on your set top box
opkg list | grep oscam    # list of available packages which contains a string "oscam"
opkg --help               # man-page (usage of opkg manager)

    Or it would certainly work well through the CAM module and insert the card into it and then insert it all into the CI + interface in the receiver.


    ////// EDIT : Did you accidentally insert the decoder card into the receiver with the reverse side? This is also a common problem when loading the correct ATR - if you remove the card and insert it back without restarting the set top box, but if you insert it the other way round, an incorrect ATR detection will occur. If so, insert the card with the correct side and restart the entire set top box (not just Enigma). However, the card should only be inserted into the receiver when it is turned off (no electricity).

    moustafa86:


    Until today I noticed that you answered a 3 month old question, marked as resolved. I'm wasting my time :). This post is old. If you don't have a new question or if you don't have a 100% solution to your problem, why do you answer?


    The answers were, in my opinion, appropriate and there were several. For example, force CAID = 1861 in the reader configuration ("oscam.server" file) to give Oscam priority and use only the Polish CAID 1861, instead of the German CAID 1860 (HD+ HD03 - DE).

    @zebr


OSCam Support Forum

Configs, discussion, downloads and guides for OSCam Softcam.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login