dm920 not read internal oscam

**xm11** · Feb 24th 2020

hello

i try to be setup orf card irdeto vershion

it not show atr of the card

i use 11572 oscam vershion

any know the problem ?

**s3n0** · Feb 24th 2020

Hi.

As first, write exactly what doesn't work in your case.

What's going on in there ? What does Oscam LOG look like ?

Only then can other discussion forum users help you.

Uhm ...

**xm11** · Feb 26th 2020

hello i got live log on oscam

it look same errore reder

2020/02/26 05:40:31 5E0E5DAF r (reader) sci1-Lower [internal] ERROR: Opening device /dev/sci0 (errno=16 Device or resource busy)
2020/02/26 05:40:31 5E0E5DAF r (reader) sci1-Lower [internal] Cannot open device: /dev/sci0
2020/02/26 05:40:33 5E0E5DAF r (reader) sci1-Lower [internal] ERROR: Opening device /dev/sci0 (errno=16 Device or resource busy)
2020/02/26 05:40:33 5E0E5DAF r (reader) sci1-Lower [internal] Cannot open device: /dev/sci0
2020/02/26 05:40:35 5E0E5DAF r (reader) sci1-Lower [internal] ERROR: Opening device /dev/sci0 (errno=16 Device or resource busy)
2020/02/26 05:40:35 5E0E5DAF r (reader) sci1-Lower [internal] Cannot open device: /dev/sci0
2020/02/26 05:40:37 5E0E5DAF r (reader) sci1-Lower [internal] ERROR: Opening device /dev/sci0 (errno=16 Device or resource busy)
2020/02/26 05:40:37 5E0E5DAF r (reader) sci1-Lower [internal] Cannot open device: /dev/sci0

my reder config

[reader]

label = sci1-Lower

description = Lower Slot

protocol = internal

device = /dev/sci0

caid = 0500

detect = cd

mhz = 480

ident = 0500:050800,050810,050820,050830,050840

group = 2

emmcache = 1,1,0,0

dropbadcws = 1

ratelimitecm = 4

ratelimittime = 0

srvidholdtime = 0

**s3n0** · Feb 26th 2020

Hello.

The basic questions are always the following:

- do you use functional configuration files ? or where do they come from ?

- have you also tried to use a clean configuration ?

- where are the other configuration files (oscam.conf, oscam.user, ...) ?

Since the error of the used slot /dev/sci0 is displayed, it is probably, as LOG looks, used by another Softcam - do you use two different Softcams ? Is your Oscam running twice with a cause of a system error (for example, incomplete uninstall of a previous Softcam) ? Don't have two Softcams installed for /dec/sci0 at the same time ?

Also very misleading is the name of this reader as "lower sci1" because it is quite possible that you have set the same hardware port for both readers, both upper and lower, and that is /dev/sci0.

Sometimes the cause of the ATR info not shown is the fact that the card is rotated to the opposite side. Thus, the chip is turned into the empty space and not to the electrical contacts in the reader inside the set top box. Unfortunately I do not see your entire "init" card from Oscam Log, but only partial. Depending on the type of error from this ATR, it can sometimes be predicted that the card is facing the right side of the chip. Therefore, try turning the card in the reader to the opposite side.

**xm11** · Feb 27th 2020

[reader]

label = sc0 srg

description = Lower Slot

enable = 1

protocol = internal

device = /dev/sci1

caid = 0500

detect = cd

mhz = 450

cardmhz = 2700

group = 1

emmcache = 1,3,15,0

blockemm-unknown = 1

dropbadcws = 1

ratelimitecm = 4

ratelimittime = 9000

ecmunique = 1

srvidholdtime = 2000

cooldown = 30,600

demo vershion

i not work two time emulator i got same errore to reder atr

i not found the problem

**s3n0** · Feb 27th 2020

Hi.

Why didn't you answer any other questions ? How am I supposed to help you ? Read again what I wrote before, please.

Just try basic config and don't add any bullshit there yet: (Back up and delete the other configuration files.)

- oscam.conf :

Code

[global]

[dvbapi]
enabled                       = 1
au                            = 1
user                          = dvbapi_user

[webif]
httpport                      = 8888
httprefresh                   = 8
httppollrefresh               = 10
httpallowed                   = 127.0.0.1,192.168.0.0-192.168.255.255,10.0.0.0-10.255.255.255

Display More

- oscam.server :

Code

[reader]
label                         = reader_sci0
protocol                      = internal
device                        = /dev/sci0
detect                        = cd
force_irdeto                  = 1
boxkey                        = A1C6F3D8B5E1F2C1
rsakey                        = 79EA25A763DA2C3E02B456A13962E60BCE63E628A2C177BE951CED96A9C6131A146F98D5867B7AE6682324FD6481913C0241F065C8D3457E54BB59B7B5DE0362
group                         = 1
emmcache                      = 0,3,15

[reader]
label                         = reader_sci1
protocol                      = internal
device                        = /dev/sci1
force_irdeto                  = 1
boxkey                        = A1C6F3D8B5E1F2C1
rsakey                        = 79EA25A763DA2C3E02B456A13962E60BCE63E628A2C177BE951CED96A9C6131A146F98D5867B7AE6682324FD6481913C0241F065C8D3457E54BB59B7B5DE0362
detect                        = cd
group                         = 1
emmcache                      = 0,3,15

Display More

- oscam.user :

Code

[account]
user           = dvbapi_user
pwd            =
group          = 1
au             = reader_sci0,reader_sci1

dm920 not read internal oscam

OSCam Support Forum

Participate now!

Share