Method of passing the rescue-image​​ for Spark devices using Cisco TFTP Server

e02d23.jpg

Method of passing the rescue-image for Spark devices using Cisco TFTP Server

In some cases Spark devices not accept soft rescue in by usb

Most of the problems of not accepting the rescue-image will be a defect from the usb that the device cannot read from

So we will use passing the rescue-image for Spark devices using Cisco TFTP Server

We connect the computer with the receiver with a regular Ethernet network cord

Then we enter the network settings into the computer

Control Panel \ Network Connections
Click properties

Then click properties on the option shown

Enter the IP address shown then ok

192.168.40.19

We put the rescue-image files without compression inside a spark folder in a specific path on a computer for example on a desktop If the receiver had stopped and it was working on the Soft spark

if he had stopped and it was on the enigma2, we would do the following

Instead of writing the name of the spark file, we will call it enigma2 and the file will also be directly in the Paragon as we mentioned before 

This trick can work But the basic principle is that the server is the Spark system

96c96b35.png

We run the program

We choose allow access

Click on view, then option

We delete the correct signs and choose the path of the spark file by clicking browse, then ok, and then we close the program For example, depending on the situation in which the receiver is located, as mentioned above

C: Desktop / spark

or

C: Desktop / enigma2

Then we close the program

We run the receiver in a Spark mode

And press ok until forc appears

Then we run the program again and do not press anything

Then we press the volume up v + button on the receiver, and the word fact appears

Then the program automatically sends the first repair file to the device

daf1db31ad64846ec72.jpg

Then the second

81846fc0f015a892.jpg

We wait until the download is finished and the word succ appears on the receiver and then booting

Enjoy & Good luck

My friend / aa7590

It is noticed from the photos that the device is downloading the software As the connection is successful The transmission is successful

Turn off the device from the back power button, then restart it. The operation can succeed

If the operation did not work,

start with this solution and implement what is contained in it

Close the device from the power button in the back and Click on the ok from the front of the receiver for 5 seconds, then not leave ok, and

open the device from power button in the back,Until it Appears on the screen is forc supported you from Ok, then you Click on the channel buttons next to it until the word spark appears on the Ok wait a little while Boot appears and the device will run.

If the operation did not work,

use the method in my topic this

Method to returns RAM load from point 0x80000000 devices Spark processor 7162 to accept Soft Rescue

Of course, all of these remote notes from some of your photos are just because I haven't seen exactly what you're doing

I am waiting for you after implementation to know the result

 Good luck

Quote from Eren21

I only have the rs232 serial port cable, my computer does not read the hyperterminal driver

This is not a program hyperterminal This is a portable program Cisco TFTP Server

The cable used is available everywhere and you can make the cable yourself

We connect the computer with the receiver with a regular Ethernet network cord

44892585be2710b8fd2ac.png

This is the original explanation from the devices manual

Upgrade Spark by TFTP 2.3.2

Since we have some restrictions and can not support all kinds of USB stick, we

provide another option (TFTP) to upgrade Enigma2/Spark

Preparation:

1. Install TFTP tools [csicotftp11.rar] to your PC

2. Set your PC IP addr to [192.168.40.19]

3. connect your PC to STB by LAN, now we only support LAN, do not support WLAN

4. Set default booting system to [spark]

Upgrade Step:

1. copy [mImage] and [userfsub.img] to any folder of your PC, for example [C:/spark

2. select folder in TFTP tools

3. Keep Pressing [OK] Button in Front Panel, then power on STB.

4. After 5 seconds you will see [Forc] in LED, release [OK] button and press [Right] Button.

5. if everything OK, You will see [T LD] shining in LED and you will see some debug

information in TFTP Server, like

“ Mon Oct 25 14:02:36 2010: Sending 'mImage' file to 192.168.40.19 in binary mode

Mon Oct 25 14:02:39 2010: Successful.

Mon Oct 25 14:02:50 2010: Sending 'userfsub.img' file to 192.168.40.19 in binary mode

Mon Oct 25 14:03:33 2010: Successful.”

6. if upgrade success, You will see [SUCC] and STB reboot automatically

The method and pictures in the topic above

44892585be2710b8fd2ac.png

Enjoy & Good luck

Quote from Bilal1980dz47

Thankx but it does not work with me

see pictures

The way works with all people follow steps in accuracy

The error here

remove the Marker From

show file transfer

enable logging

As picture

Use Soft Rescue private for Your box What is your box type

Quote from Bilal1980dz47

SUPERBOX SPARK S750

Go to the page on the following link To download the appropriate software for your device

SuperBox Spark S750 satellite Receiver Software, Tools - Mr-Dish

SuperBox Spark S750 High Definition Satellite Receiver Features FULL HD 1080p Output SB 2.0 Host ports (MP3 Player and JPEG Viewer) USB upgradeable, with the…

www.mr-dish.com

Quote from Bilal1980dz47

NO way all files in this link are fake and not found

Go to the page on the following link

Super Box Receiver Software

worldsatellitehouse.blogspot.com

Quote from Bilal1980dz47

not helpful just advtissements

Try here

Софт для SuperBOX SPARK S-750 - Alensat