my friends
We got to version 226
The error still exists and the team is trying to fix it
There is no need to hurry downloading the copy until the repair is completed
There are 525 replies in this Thread which was already clicked 142,307 times. The last Post () by ahmed gazye.
my friends
We got to version 226
The error still exists and the team is trying to fix it
There is no need to hurry downloading the copy until the repair is completed
Display Moremy friends
We got to version 226
The error still exists and the team is trying to fix it
There is no need to hurry downloading the copy until the repair is completed
Did you test r226 yourself?
No, I did not test the version myself, but
Fri Aug 28, 2020 9:44 am
r226 image from mediafire installed and tested.
The remote control does not work, but Webif is available again.
Display Moreprofessor / Persian Prince
No, I did not test the version myself, but
From your site on the subject, the post says that the problem still exists
Re: spark7111
Fri Aug 28, 2020 9:44 am
r226 image from mediafire installed and tested.
The remote control does not work, but Webif is available again.
That's for ufs912 not spark, spark fixed.
The topic in your site is private spark 7111
In general, thank you for you & your team for what you offer us, and the experience will be done soon, God willing
openvision-enigma2-develop-extralanguage-gstreamer-10.2-r226-spark_usb.zip
Thank you very much, dear friend / BarviX
We invite all friends to try the version until it is known if it has been confirmed that the copy is fixed
openvision-enigma2-develop-10.2-r226-spark
The team is now in version 227
Version was built by our wonderful friend / BarviX
Please, our wonderful friend / BarviX, have you tried the version and the fix was done?
We thank you again for your support and hope for more
my friends
I test the version on my Spark 7162 on the external flash using the plugin Nfr4X Multiboot of Opennfr
The installation was successful after several attempts, the version takes about 10 minutes to boot or to cross the version. a screenshot cannot be taken from the OpenWebif plugin, but by the plugin ShootYourScreen Format Screen Shot png only the remote works on the version
We thank again dear friend / BarviX
& Persian Prince & wonderful OpenVision team
My friends
openvision-enigma2-develop-extralanguage-gstreamer-10.2-r227-spark_usb.zip
https://runigma.com.ua/feeds/i…-r227-spark.rootfs.tar.gz
https://runigma.com.ua/feeds/i…r-10.2-r227-spark_usb.zip
Thank you for the effort.
I installed it on Truman Premiere Plus, unfortunately nothing appeared on screen except the booting image then the receiver kept showing HDMI and SCART.
Any idea to solve this issue.
Thanks again.
Thank you for the effort.
I installed it on Truman Premiere Plus, unfortunately nothing appeared on screen except the booting image then the receiver kept showing HDMI and SCART.
Any idea to solve this issue.
Thanks again.
You just have to wait for the version to stabilize and the settings are shown clearly the version takes about 10 minutes to boot or to cross the version
Thanks for the tip. I waited 15 minutes and still the same.
I switched to version 9.3 rev92.
Thanks for the tip. I waited 15 minutes and still the same.
I switched to version 9.3 rev92.
I did not install the version on my device because I installed the version 226 of the friend / BarviX , as you can see on the post above, and it works fine switched to version 226 it works fine
aedessa & my friends
If there is any error in the copy, it must be written to the team on its site until the correction is done
For those who face a problem with the remote in this version
This solution is provided by our friend / Worldcup for those who like to experience
First of delet old files from etc all lircd files and send a new files and receiver is restart then rc is 10000...% ok
http://www.mediafire.com/file/41czob35t3d6key/etc.zip/file
but this is a temporary solution must be written to the team on its site until the correction is done r the next versions
Help,Grab not work!!
Hey bro,
I tested this image on Truman Premier Plus but no video coming to screen.
Can you solve this issue. Thanks
Hey bro,
I tested this image on Truman Premier Plus but no video coming to screen.
Can you solve this issue. Thanks
Connect your TV to avi or scart then you should see the screen ,then go to audio video change bybass hdmi to disable then change to hdmi the screen should work fine
Display MoreHey bro,
I tested this image on Truman Premier Plus but no video coming to screen.
Can you solve this issue. Thanks
Connect your TV to avi or scart then you should see the screen ,then go to audio video change bybass hdmi to disable then change to hdmi the screen should work fine
Thanks. I followed the steps but it freezes after select language and remote control not working as well.
Don’t have an account yet? Register yourself now and be a part of our community!