Infinity Usb Unlimited // Ubuntu 20.4 // how to....Help!

Hello everybody!

i have installed ubuntu 20.4 lts

also i connected infinity usb unlimited

------

in lsusb it regognize it 008:002 and /dev/ttyUSB0

------

i use in oscam.server the below.....

[reader]

enable = 1

label = card

protocol = smartreader

device = 008:002

detect = cd

-- after a litle says reader device error

----------------------

if i put protocol mouse

and device= /dev/ttyUS0 ....the webif dont even open

--------------------

Can you help me infinity usb unlimited to work with oscam and ubuntu 20.4lts ?

tks a lot!!

-----------------

Oh ...i forgot to say that the oscam.bin is compatible with smartreader///mouse///phoenix////etc....

reader device error again Admin :(

here is the log

not Work Admin....

here is new log....

ok i run again give me 10 seconds

Now just give me ERROR and not CARD OK.....i think its an improovment !

here is the log my Admin....

[reader]

enable = 1

label = card

protocol = mouse

device = /dev/ttyS0

detect = cd

mhz = 600

cardmhz = 369

caid = 09BE

ident = 09BE:000000

ecmwhitelist = 09BE:71,6E,78,3A

boxid = xxxxx

ins7e =

k1_unique =

ins7e11 = 15

group = 1

emmcache = 1,3,2,0

blockemm-unknown = 1

blockemm-u = 0

blockemm-s = 1

blockemm-g = 1

saveemm-unknown = 1

saveemm-u = 1

audisabled = 0

disablecrccws = 1

ndsversion = 2

read_old_classes = 0

ok My Admin Thank you for all your help

i will try .......

Do you know where i can download ..... iuu_phoenix-2.6.21.ko and iuu_phoenix-2.6.22.ko prebuilt modules

i cant find nowhere!!!!

This module provide a serial interface to use your

IUU unit in phoenix mode. Loading this module will

bring a ttyUSB[0-x] interface. This driver must be

used by your favorite application to pilot the IUU

This driver is still in alpha stage, so bugs can

occur and your system may freeze. As far I now,

I never had any problem with it, but I'm not a real

guru, so don't blame me if your system is unstable

You can plug more than one IUU. Every unit will

have his own device file(/dev/ttyUS0,/dev/ttyUSB1,...)

How to install it ?

A.Compile yourself

1. Prepare your kernel 2.6.21 an up

2. Compile it with usbserial enabled

3. install it as usual

4. cd into V2.6 directory

5. type 'make all'

B.Use prebuilt modules

iuu_phoenix-2.6.21.ko and iuu_phoenix-2.6.22.ko

are provided for those who are unable to compile

kernels.

You can directly use insmod with the right module like this:

insmod -f iuu_phoenix-2.6.21.ko ( or 2.6.22.1 )

How to tune the reader speed ?

A few parameters can be used at load time

To use parameters, just unload the module if it is

already loaded and use modprobe iuu_phoenix param=value.

In case of prebuilt module, use the command

insmod iuu_phoenix param=value.

Example:

modprobe iuu_phoenix clockmode=3

The parameters are:

parm: clockmode:1=3Mhz579,2=3Mhz680,3=6Mhz (int)

parm: boost:overclock boost percent 100 to 500 (int)

parm: cdmode:Card detect mode 0=none, 1=CD, 2=!CD, 3=DSR, 4=!DSR, 5=CTS, 6=!CTS, 7=RING, 8=!RING (int)

parm: xmas:xmas color enabled or not (bool)

parm: debug:Debug enabled or not (bool)

- clockmode will provide 3 different base settings commonly adopted by

different software:

1. 3Mhz579

2. 3Mhz680

3. 6Mhz

- boost provide a way to overclock the reader ( my favorite :-) )

For example to have best performance than a simple clockmode=3, try this:

modprobe boost=195

This will put the reader in a base of 3Mhz579 but boosted a 195 % !

the real clock will be now : 6979050 Hz ( 6Mhz979 ) and will increase

the speed to a score 10 to 20% better than the simple clockmode=3 !!!

- cdmode permit to setup the signal used to inform the userland ( ioctl answer )

if the card is present or not. Eight signals are possible.

- xmas is completely useless except for your eyes. This is one of my friend who was

so sad to have a nice device like the iuu without seeing all color range available.

So I have added this option to permit him to see a lot of color ( each activity change the color

and the frequency randomly )

- debug will produce a lot of debugging messages...

Last notes:

Don't worry about the serial settings, the serial emulation

is an abstraction, so use any speed or parity setting will

work. ( This will not change anything ).Later I will perhaps

use this settings to deduce de boost but is that feature

really necessary ?

The autodetect feature used is the serial CD. If that doesn't

work for your software, disable detection mechanism in it.

Have fun !

Alain Degreffe

can you help me with ubuntu commands step by step please my Admin?

i cant understant anything!!!

i have install infinity utility in windows already

----

not Smart but unlimited which i have

in laptop i have windows

in desktop i have ubuntu