[HOW-TO] Dinobot Update Android Firmware

There are 28 replies in this Thread which was already clicked 9,967 times. The last Post () by winter1.

    I think it is useful to do some clarity and you will see that everyone will succeed.



    356027690615540a3.jpg




    The latest file on Dinobot-Hitube is ONLY an update, so if you don't already have Android 8.0 installed it WILL NEVER INSTALL.


    You need a USB stick formatted in FAT 32

    (make sure it has no problems maybe with a special prg) and inserting it sideways (I used the usb1 slot).


    Everything with the decoder off, then turn it on and immediately press OK on the remote control several times until the display shows


    "UPDT".


    SO LET'S START !!!

    If you have Android 7.0,


    "always check carefully in the name that there is the wording of your decoder"



    1.Load the full version of Android 8.0 via USB PEN (which you can find on the FB Dinobot-Hitube post site dated November 15, 2019)

    For U5 Mini

    Code
    https://mega.nz/file/y8MxEKKC#lsTUGQDLrn6MvZNrHRKo19wgiy6w_j8bRQJdA79OqcQ


    For 4k

    Code
    https://mega.nz/file/G18UhaIK#hpCQ_7E65djMboua6igjCXtWnjZdYHzPGOleFmeZD2o


    2. update online from the decoder,


    3. upload via USB PEN (the file also posted on FB on April 14th)

    -Dinobot 4k + 20210406 u5plus

    Code
    https://mega.nz/file/zpkw3CrD#ghN1FklSvPQ7l9YAE6XYhmmVTD3Ai1LXVOsasnxtfKY


    -Dinobot U5Mini 20210405:


    Code
    https://mega.nz/file/v8FjiIbY#B48mKsG6qZMODKJC6R1jRq6DcoqA7z604Mct-1Z4vaA




    NB:

    -If the box does not start E2 and LiveTV has the error "No adapter detected", continue with the next steps.


    -Download 20210407: (u5plus)

    Code
    https://mega.nz/file/zpkw3CrD#ghN1FklSvPQ7l9YAE6XYhmmVTD3Ai1LXVOsasnxtfKY



    and you will finally see that you will no longer see robots belly up!



    the files you download must all be ONLY renamed to update.zip and copied on a pen and not unzipped.


    Now you "have" to succeed



    End HowTo




    ======================


    ATTENTION

    after UPDATE full, when you restart your box you don't have Enigma2 ???

    The fact is that the Android installation, uses a blank MAC address

    and therefore needs your correct MAC address to boot

    The MAC address is the one on the box or bottom of the Dinobot.

    You have to enter your MAC address in a mac.txt file and put it on a USB stick.

    In the following format.

    00: 00: 00: 00: 00: 00

    replace the zeros with your mac address, then create a blank text file enter the receiver

    mac details and save it as mac.txt on a USB stick.

    Now to use this mac address on your Box you need to boot - load Android.

    Go to the LIVE TV app

    Go to setup ... Various ... preferences

    At the bottom of the menu you will see a "Write Mac Serial Number" option.

    Click on it to set the new MAC from the USB stick.


    -Oscam is embedded

    -----Open LiveTv and Press Menu 2580
    -----Open Browser ip_box:port for oscam view

    add reader atc etc.


    Now go back to the Android ATv menu you have to select Use E2.






    RECOVERY (IF IT JUST GOES WRONG) :shock:


    Download this file:


    -Dinobot 4K + Normal: update.zip - Google Drive

    Code
    https://drive.google.com/file/d/1J5rb8rnOmDblbIXR9LwSojQpjRIkmFUq/view


    Includes Android and E2 openATV


    Dinobot Full pictures for recovery

    Update 2018-07-02

    Don't unpack.

    Update.zip to an empty USB stick.


    • Turn off the BOX from the main switch,
    • insert the USB key on the back,
    • press the Reset button on the back,
    • keep it pressed,
    • turn on the main switch until Update appears on the display,
    • then wait until the Box restarts



    Thank's Acherone



    ****

    for other update and issue please read KiddaC post

    Dinobot 4K Update - Including missing E2 afterwards ( Solved )


    here Other topic to:


    How to "flash" a Dino... and his brothers and sisters...

    Android OSCAM EMU for DINOBOT/U5PVR


    OLD TOPIC UPDATE 2019


    Other Info here

    Quote

    https://www.facebook.com/groups/1018591428653469/

    Setting Editor

    DogStrike's setting editor for the dinobot

    Android 8.0 -> Android 7.0 (downgrade)



    Code
     https://drive.google.com/file/d/1p5W3Hm8dRe5OOMbewviRaHBC_GCdW0EX/view


    Install the following firmware using a USB stick.


    Then perform the following steps


    1. Go to .... system update ... online update - complete installation

    2. Automatic restart, no E2 available

    3. Create a mac.txt file in the USB with the correct Mac address 00: 00: 00 00: 00: 00

    4. You can find the Mac address during installation in the menu or under your device on the


    5. Restart the box: now you can select E2 using the colored key.


    6. Now install the E2 image - download it - copy the Dinobot folder to USB


    and at start-up, press the green button several times until UPDTE appears on the display



    Adapted from:

    Code
    https://www.opena.tv/dinobot-4k-mini/46562-dinobot-u5mini-downgrade-atv8-0-zu-atv7-0-a.html

    Ciao ho provato i vari modi da te descritti non va ,sempre lo stesso .

    Peccato Facendo prove mentre caricava il file android update si e' spento morto mi sa che e' irrecuperabile .Se qualcuno sa cosa fare lo ringrazio .Comunque Grazie lo stesso lululla.

    Edited 3 times, last by winter1 ().

    Sorry I don't speak English I help myself with the translator, I hope you understand.I tried the various ways described above but it doesn't work, only android started, now doing tests while loading the android update file is turned off and not even Android starts again, ' (black display does not turn on) I think it is irrecoverable.

    Is there any guide how to make it resurrect (reprogram it)?

    Edited once, last by winter1 ().

    if only android worked, you had to insert a .txt file with your mac inside and import it from LiveTv

    Now you have complicated things.

    You didn't read everything before you started.

    I don't know if it can be resurrected. I hope so.

    Try

    RECOVERY (IF IT JUST GOES WRONG)

    Do not take even a minute away from the affection of those who love you: you would not have time to recover it!


    Have a Good Trip


    GOOD VPN



    DMU


    logo_corvo.png


    Hi LULULLA made the programming with HITOOL and I recovered the DINOBOT 4K + decoder all went well, I loaded first (opennfr_hitool_recovery_anadol4k) and then I loaded (anadolcombo_recovery_20190319 ok later with USB) now I find an ANADOL COMBO 4K image. Only E2 without ANDROID.

    I tried to upload the update file as per the procedure I go to upld but it does not load anything I only have E2 left.I searched the web to find a file x dinobot 4k plus but I did not find anything can you help me? .A thousand thanks

    Edited 2 times, last by winter1 ().

    I'm glad you got your dinobot back

    I have no idea now how you can do it

    but i guess you just need to send a recovery backup for 4k

    Read carefully the procedure at the first post of the topic

    Send recovery for 4k via usb (android)

    Please do not make mistakes now, at your own risk

    Ich habe versucht, die Datei update.zip für Dinobot 4k zu installieren + nichts zu tun Ich halte Reset Ich schalte den Decoder ein Ich gehe zu upld, aber Android wird nicht geladen, wenn es nach dem Booten neu startet, Menü, nur e2 Ich kann Android nicht auswählen, weil es ist nicht installiert.


    Google translate by Moderator


    I tried to install the update.zip file for Dinobot 4k + nothing to do I keep reset I turn on the decoder I go to upld but Android won't load when it reboots after booting, menu, only e2 me cannot select Android because it is not installed.

    • Official Post

    winter1 Only English language in this forum if you need to get help.

    There is a section for German language if you want to use German langugae

    -------------------------------------------------------------------------------------------------

    Everything in life that's any fun is either immoral, illegal or fattening

    If you want to support the Linuxsat-Support forum

    Become a VIP Member

    Quote from winter1

    Ich habe versucht, die Datei update.zip für Dinobot 4k zu installieren + nichts zu tun Ich halte Reset Ich schalte den Decoder ein Ich gehe zu upld, aber Android wird nicht geladen, wenn es nach dem Booten neu startet, Menü, nur e2 Ich kann Android nicht auswählen, weil es ist nicht installiert.


    Google translate by Moderator


    I tried to install the update.zip file for Dinobot 4k + nothing to do I keep reset I turn on the decoder I go to upld but Android won't load when it reboots after booting, menu, only e2 me cannot select Android because it is not installed.

    with this

    [HOW-TO] Dinobot Update Android Firmware
    have you tried to downgrade?


    I don't know how I can help you I don't have this problem, luckily it hasn't happened to me yet but I think if you find the right / boot file you can.

    Do not take even a minute away from the affection of those who love you: you would not have time to recover it!


    Have a Good Trip


    GOOD VPN



    DMU


    logo_corvo.png


    Thank you lululla x your interest I have tried but nothing to do my problem is that I have enigma2 installed, but I cannot install ANDROID. po goes into updt it restarts after a very short while without installing anything and I am just enigma2 as in the beginning.


    I have lost Android and dual boot capabilities.

    Edited once, last by winter1 ().

    can any one help me to get ATV8 dual boot for U5 PVR deluxe/se or dinobot 4k se ( dinobot 4k se ATV 8 upgrade INCLUDING MISSING E2 )

    I upgrade online ATV 8 not include E2 even in the MISC not exist after adding MAC address no way can you help please

    Quote from m.ghattas

    can any one help me to get ATV8 dual boot for U5 PVR deluxe/se or dinobot 4k se ( dinobot 4k se ATV 8 upgrade INCLUDING MISSING E2 )

    I upgrade online ATV 8 not include E2 even in the MISC not exist after adding MAC address no way can you help please

    request here


    Quote

    https://www.facebook.com/groups/1018591428653469/


    and report please

    Do not take even a minute away from the affection of those who love you: you would not have time to recover it!


    Have a Good Trip


    GOOD VPN



    DMU


    logo_corvo.png


Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login