Wireguard VPN

There are 22 replies in this Thread which was already clicked 3,711 times. The last Post () by urie.

  • Weil OpenVPN nicht genug ist ;)

    I habe Wireguard in OpenATV 6.4 installiert:


    314b5c7821208d029.jpg


    Eine mjnhubngh5.conf Datei von einem kostenlosen Wireguard Server heruntergeladen und in /etc/wireguard/ abgelegt.


    Wenn ich aber den Befehl ausführe ....

    Code
    wg-quick up mjnhubngh5


    Habe folgendes:


    f70f84f0d4.jpg


    Meine IP Adresse bleibt dieselbe.


    Ich vermute stark, dass ich da was falsch mache (?)

    ZGemma H9S SE - OpenATV 7.3

    Edited 2 times, last by s2gus24 ().

  • Ja wireguard und E2 ist eine Sache für sich lässt sich nicht so einfach nutzen auf der Box kenn zumindest keine der direkt auf der e2 laufen hat ja es gibt da bei DreamOS wireguard mit den nötigen depends nicht aber soweit ich weiß auf oe2.0


    Falsch hast du nichts gemacht


    wg-quick up xxx


    Ist schon richtig


    Was sagt ifconfig nach dem WG connect ?

  • Ja läuft halt nur auf den zwei Dreamboxen aber halt auf jeden Raspi.


    Obwohl das WireGuard Plugin von murxer schon sehr stark ist. Du kannst die Box als Server oder Client einsetzen somit entstehen damit auch ein paar schöne Möglichkeiten in einigen Bereichen. :rasta:

  • Wireguard funktionniert als Server aber auch als Client (selbst ausprobiert) in OpenSPA-7.5.005 (19 Februar 2022)

    Ich weiß nicht, ob dies als Ausgangspunkt in Betracht gezogen werden kann um eine funktionierende Lösung für OpenATV zu finden.

    ZGemma H9S SE - OpenATV 7.3

    Edited once, last by s2gus24 ().

  • Ja weil du immer auf e2 rum

    Reitest :smiling face with sunglasses:

    nimm einfach raspi und gut ist

    Ich habe zwar noch einen Raspberry Pi der ersten Generation rumliegen, aber ich hätte gerne eine kompaktere Lösung ;)

    FritzOS 7.50 wird bald kommen und Wireguard ist ohnehin integriert.

    Am liebsten wäre mir, wenn die Möglichkeit für OpenATV gäbe.

    ZGemma H9S SE - OpenATV 7.3

  • Ciao

    Io utilizzo wireguard vpn ormai da due anni e va che e' una meraviglia.

    Lo utilizzo direttamente nel router e cosi sono proteto su tutto, ricevitore sat, pc, ipad ecc..ecc..

    Ti basta un semplice router che sia compatibile con protocollo wireguard da mettere in cascata al router principale,io uso ad esempio un "GL-AR750" dal costo inferiore ai 50 euro e va una favola.

  • Ciao

    Io utilizzo wireguard vpn ormai da due anni e va che e' una meraviglia.

    Lo utilizzo direttamente nel router e cosi sono proteto su tutto, ricevitore sat, pc, ipad ecc..ecc..

    Ti basta un semplice router che sia compatibile con protocollo wireguard da mettere in cascata al router principale,io uso ad esempio un "GL-AR750" dal costo inferiore ai 50 euro e va una favola.

    Hi,

    I totally subscribe to this point of view. However, the reason why I'd like to have a Wireguard client on the box itself is the same that made me choose an open source operating system with all its bells and whistles, as simple as that.

    ZGemma H9S SE - OpenATV 7.3

  • Es geht weiter .....


    Code
    root@zgemmah9sse:~# wg-quick up Wg0
    [#] ip link add Wg0 type wireguard
    [#] wg setconf Wg0 /dev/fd/63
    [#] ip -4 address add 10.2.0.2/32 dev Wg0
    [#] ip link set mtu 1420 up dev Wg0
    [#] resolvconf -a Wg0 -m 0 -x
    /sbin/resolvconf: illegal option -- x
    [#] ip -4 route add 0.0.0.0/1 dev Wg0
    Code
    root@zgemmah9sse:~# ping -c 3 XXX.183.XX.XX
    PING XXX.183.XX.XX (185.183.33.11): 56 data bytes
    64 bytes from XXX.183.XX.XX: seq=0 ttl=58 time=35.566 ms
    64 bytes from XXX.183.XX.XX: seq=1 ttl=58 time=33.382 ms
    64 bytes from XXX.183.XX.XX: seq=2 ttl=58 time=33.420 ms
    
    --- XXX.183.XX.XX ping statistics ---
    3 packets transmitted, 3 packets received, 0% packet loss
    round-trip min/avg/max = 33.382/34.122/35.566 ms


    Das Plugin IP Checker zeigt die IP Adresse des VPN Providers (XXX.183.XX.XX)

    Code
    wget -O - -q http://checkip.dyndns.org/

    .... zeigt aber meine reale IP Adresse!


    Das obige habe ich mit AllowedIPs = 0.0.0.0/1


    AllowedIPs = 0.0.0.0/0 erzeugt den Fehler (iptables-restore v1.8.7 (legacy): iptables-restore: unable to initialize table 'raw')

    AllowedIPs = 0.0.0.0/1, 128.0.0.0/1 erzeugt keinen Fehler, habe aber keine Internetverbindung!

    ZGemma H9S SE - OpenATV 7.3

    Edited 7 times, last by s2gus24 ().

Forum Deutsch LinuxSat

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!