Samur's OSCam - Request for compilation, questions and help !!!
-
- Various Support
- samur
- Thread is marked as Resolved.
-
-
one question, why this oscam "callin´ home? ip from from 172.105.020.139?
-
Hi samur, I can't try it, I have a box with a mips processor, sorry, thank you
-
one question, why this oscam "callin´ home? ip from from 172.105.020.139?
I think you are from those who are making trouble in cz/sk forums ...
because private binaries with money stopped.
Ex: From slovak forum we can read messages like this one:
QuoteDon't use oscam from samur because a backdoor implemented on it...etc
So, if you want a ban then it will takes 10 secondes.
...
;
-
I'll try it when I get home and let you know. On my RPI4. Definitely. Thank you samur
-
Hi samur, I can't try it, I have a box with a mips processor, sorry, thank you
add needsemmfirst = 1 to the reader is mandatory
and report ...
-
one question, why this oscam "callin´ home? ip from from 172.105.020.139?
You have a change so you don't get bored, it was last time 84.19.76.119
-
I'll try it when I get home and let you know. On my RPI4. Definitely. Thank you samur
add needsemmfirst = 1 to the reader is mandatory
replace the binary save and restart
is the decryption start after a little time or immediately ? because with: needsemmfirst = 0 it will takes 10 min to start decrypt(valid CW)
if there is something wrong then report ...
-
one question, why this oscam "callin´ home? ip from from 172.105.020.139?
I think you are from those who are making trouble in cz/sk forums ...
because private binaries with money stopped.
Ex: From slovak forum we can read messages like this one:
QuoteDon't use oscam from samur because a backdoor implemented on it...etc
So, if you want a ban then it will takes 10 secondes.
...
;
ok, you dont answer if it is true. i think you may say it is not true.I won't discuss it.ok, sorry
-
Dreambox TWO, image last experimental 24.02.2022.
For me, either OSCam r11748-800 or OSCam r11750-800, the 0624 card starts up after a long time and it doesn't matter if I have needsemmfirst = 0 or needsemmfirst = 1
I won't tell you the exact time it will start, because I didn't want to wait and wait for it to start.
Icam SkyDE stations connected to the sharing server run fine.
I can't try AFN AU because I don't have a 9E LNB.
-
Hi Samur,
For me ICAM not working with your OSCam r11750-800 (VU+ Duo 4K SE), but with 11734 - everything is OK - where is a problem?
-
AU on AFN powerVU is not working for me
i still don't know why exactly we have this problem of AU on PowerVu ...
AU works but sometimes you need to wait on channel 30 to 50 minutes ...
;
The PowerVu EMMs of AFN are sent in a loop with a break of around 10-15 minutes where nothing is sent. Then the loop starts again.
It is many years since I last looked at this, but IIRC the total time taken to send all the EMMs to each box was around 1 hour.
How long it takes to get a hit depends upon the keys you have and when you "join" the loop.
The more keys you have and if they are equally distributed through out the range - means you get a quicker AU.
-
AU on AFN powerVU is not working for me
i still don't know why exactly we have this problem of AU on PowerVu ...
AU works but sometimes you need to wait on channel 30 to 50 minutes ...
;
The PowerVu EMMs of AFN are sent in a loop with a break of around 10-15 minutes where nothing is sent. Then the loop starts again.
It is many years since I last looked at this, but IIRC the total time taken to send all the EMMs to each box was around 1 hour.
How long it takes to get a hit depends upon the keys you have and when you "join" the loop.
The more keys you have and if they are equally distributed through out the range - means you get a quicker AU.
Thanks bud that makes sense, i have now added a load of EMM keys found on the net.....
TBH i have no idea which of them even work / not work..... i dont currently have anyway of recording the full .ts stream
off to work shortly but will leave it on ands see if get keys to roll.....
-
I'll try it when I get home and let you know. On my RPI4. Definitely. Thank you samur
add needsemmfirst = 1 to the reader is mandatory
replace the binary save and restart
is the decryption start after a little time or immediately ? because with: needsemmfirst = 0 it will takes 10 min to start decrypt(valid CW)
if there is something wrong then report ...
I changed to the latest version oscam, restarted the entire RPi4 and within 3 minutes I had an image. well thank you samur
-
Dreambox TWO, image last experimental 24.02.2022.
For me, either OSCam r11748-800 or OSCam r11750-800, the 0624 card starts up after a long time and it doesn't matter if I have needsemmfirst = 0 or needsemmfirst = 1
Thank you very much
;
-
-
Hi samur test on vu solo2 mips for me either OSCam r11748-800 or OSCam r11750-800 the 0624 card starts after a long time about 10 minutes you have to wait and it doesn't matter if I have needemfirst = 0 or needemfirst = 1 anyway thanks .
-
Check if AFN and ICam are OK.
Both are working perfectly on VU+ULTIMO4K
A job well done
-
Hi samur test on vu solo2 mips for me either OSCam r11748-800 or OSCam r11750-800 the 0624 card starts after a long time about 10 minutes you have to wait and it doesn't matter if I have needemfirst = 0 or needemfirst = 1 anyway thanks .
;
-
returned to the old things
This one runs OK again like a Swiss watch. Both the local card 0624 and the shared Icam card.
If you have time and inclination, send me the ARM version for Octagon 8008 and I'll try it right away.
OSCam-EMU Support Forum
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!