[Plugin] WireGuard VPN by Madhouse

If to switch from proton vpn in which one to go working fine?

Regards to all.

Simply download a wireguard configuration on your proton portal and use it with the plugin.

I am using NordVPN and I am 99% of the way there.

I have my access token. The private key was generated. The server list is shown.

But when I attempt to connect to any server it does say 'Connection established' but am still on my IP. When I attempt to connect multiple times the box appears to do a gui reboot. No crash logs are generated. I do not have OpenVPN installed.

I'm running OpenATV 7.5.1, python 3.12.9. I'll keep trying and if I solve it I will get back to you.

Quote from madhouse

Quote from ThinksAmoral

I am using NordVPN and I am 99% of the way there.

I have my access token. The private key was generated. The server list is shown.

But when I attempt to connect to any server it does say 'Connection established' but am still on my IP. When I attempt to connect multiple times the box appears to do a gui reboot. No crash logs are generated. I do not have OpenVPN installed.

I'm running OpenATV 7.5.1, python 3.12.9. I'll keep trying and if I solve it I will get back to you.

Display More

On which receiver?

Telnet:

/etc/init.d/wireguard stop

/etc/init.d/wireguard start

After sending the start command, paste the output you receive.

Display More

I'll start by saying I fixed it thanks to your telnet command.

It is an Edision OS mio 4k plus. This was the telnet:

root@osmio4kplus:~# /etc/init.d/wireguard stop
Stopping Wireguard interface: wg0
wg-quick: `wg0' is not a WireGuard interface
root@osmio4kplus:~# /etc/init.d/wireguard start
Internet connection OK
Starting Wireguard interface: wg0
[#] ip link add wg0 type wireguard
[#] wg setconf wg0 /dev/fd/63
[#] ip -4 address add 10.28.140.95 dev wg0
[#] ip link set mtu 1420 up dev wg0
[#] resolvconf -a wg0 -m 0 -x
[#] ip -6 route add ::/1 dev wg0
Error: IPv6 is disabled on nexthop device.
[#] resolvconf -d wg0 -f
[#] ip link delete dev wg0
root@osmio4kplus:~#

When I noticed the error I went into settings and set 'Disable ipv6' to No and retried to connect. It worked.

hi

tried to install on openatv 7.6 which i have dreambox one but i get this message is there other way to install this ?

thanks

Quote from rahimi29

hi

tried to install on openatv 7.6 which i have dreambox one but i get this message is there other way to install this ?

thanks

Hello,

Look the first post. The supported architecture are written close to the python version (ex: arm).

Your log is pretty clear, unfortunately your architecture (aarch64) isn’t yet supported.

In my opinion you have to look for another VPN manager.

Greetings

@until061

thanks for respond

hello madhouse for python 3.9 I saw I didn"t update it could you also do it thank you very much

There is a problem with the updated arm python "3.13" link on page 1.

@madhouse

thanks alot for a quick fix

Like this you mean ?

Its very easy, you just have to write a converter which looks for the wg0 file used by Wireguard and then add the appropriate widgets to your skin so it calls upon it.

Quote from ian1095

Like this you mean ?

Its very easy, you just have to write a converter which looks for the wg0 file used by Wireguard and then add the appropriate widgets to your skin so it calls upon it.

Thanks for the reply, but unfortunately I am not a programmer and everything I do is trial and error following intuition and common sense, combining parts of code that I find already done on various skins.
Maybe if I could have what is necessary for the VPN indication that you added above the title of the film I could try to integrate it into my skin.
Greetings