Hi, I need help to get my motor dish to work with scr (unicable) lnb.
My decoder 1 is a dm800se. I have set it up to work with a motorized dish with USALS d with a legacy lnb. The cable from the decoder 1 is attached to the motor and then from motor out to the lnb. Whit this configuration every thing is fine.
My lnb has a SCR input and two legacy output. The above configuration works fine when the output of the motor is attached to a legacy input of the lnb.
Now I need to use the SCR input of my lnb because I need to attach decoder 2 that uses channel 1 & 2 of the SCR. THe dish is set at 13.2° Hotbirt satellite. I have connected the output of the dish motor to the lnb scr input. I have also set up a splitter (dc pass in one direction only ) so that I can have decoder 1 e decoder 2 using the same disch cable.
I also have changed the configuration of decoder 1 to use channel 3 of SCR and decoder 2 to use channel 1 & 2 of SCR.
Both the decoder are working ok with the motor dish set at 13.2 East.
Decoder 2 has only Hotbird channel settings, while decoder 1 has the motorized channel settings.
With this configuration the motor is not working anymore and I cannot get any other channels on other satellites besides Hotbird. If 1 on my decoder I switch to a channel that is on Astra for example I get 0% signal. I also have checked and confirmed that the dish is not moving at all.
Below is my tunet configuration taken out of the enigma2 setting file:
config.Nims.0.scpcSearchRange=1
config.Nims.0.diseqcA=3601
config.Nims.0.diseqcB=3601
config.Nims.0.diseqcC=3601
config.Nims.0.diseqcD=3601
config.Nims.0.configMode=advanced
config.Nims.0.longitude=17.300
config.Nims.0.diseqcMode=positioner
config.Nims.0.latitude=40.0
config.Nims.0.advanced.sats=130
config.Nims.0.advanced.lnb.1.lof=unicable
config.Nims.0.advanced.lnb.1.powerMeasurement=false
config.Nims.0.advanced.lnb.1.sequenceRepeat=true
config.Nims.0.advanced.lnb.1.unicableLnbManufacturer=Telestar
config.Nims.0.advanced.lnb.1.longitude=17.300
config.Nims.0.advanced.lnb.1.unicableLnb.Radix.product=Unicable LNB
config.Nims.0.advanced.lnb.1.unicableLnb.Radix.vco.Unicable LNB.2=2040
config.Nims.0.advanced.lnb.1.unicableLnb.Radix.scr.Unicable LNB=3
config.Nims.0.advanced.lnb.1.unicableLnb.Telestar.product=Skywire HC LNB
config.Nims.0.advanced.lnb.1.unicableLnb.Telestar.vco.Skywire HC LNB.1=1420
config.Nims.0.advanced.lnb.1.unicableLnb.Telestar.vco.Skywire HC LNB.0=1210
config.Nims.0.advanced.lnb.1.unicableLnb.Telestar.vco.Skywire HC LNB.3=2040
config.Nims.0.advanced.lnb.1.unicableLnb.Telestar.vco.Skywire HC LNB.2=1680
config.Nims.0.advanced.lnb.1.unicableLnb.Telestar.scr.Skywire HC LNB=4
config.Nims.0.advanced.lnb.1.diseqcMode=1_2
config.Nims.0.advanced.lnb.1.uncommittedDiseqcCommand=1
config.Nims.0.advanced.lnb.1.diseqcRepeats=three
config.Nims.0.advanced.lnb.1.latitude=40.0
config.Nims.0.advanced.sat.3601.lnb=65
config.Nims.0.advanced.sat.130.lnb=1
What Have I done wrong ?
How can I get my syten working ?
