EGAMI 10.6 - R3 /OE-A 5.5.1/ PYTHON 3.12.8

I also installed Egami but I have a problem similar to the one on the OpenAtv image. I have an H7C, on the satellite side Tuner A I have a multifeed, on the cable side at Tuner B I have Digi Cable and at Tuner C I have the Mindig Tv terrestrial antenna, I mention that this configuration works without problems on OpenVix, OpenBh, OpenPli.

Now the problem, after scanning I can't see the stations on Tuner C, it shows that I have no signal. If I change the setting in Preferred Tuner, the stations on Tuner B no longer work, no matter what settings I make, only one input works on the DVBC/T side, as seen in the pictures. I mention that the scan works OK, it finds all the stations on all the tuners. I hope I made myself understood and I can find help from my colleagues.

Sorry use translate.Screenshot 2024-11-20 121348.png

Screenshot 2024-11-20 121657.png

Screenshot 2024-11-20 122046.png

hello

I configured it correctly, I'm not the first to install an image, but I only experienced this on Openatv and now on Egami, I really like the image. If I enter the preferred tuner and put the preferred tuner C, the terrestrial works, but the B tuner, i.e. cable, no longer works. For the preferred tuner, I normally use AUTO.

Hi, I have to give some advice to those who install Egami (very nice) on how to start the software and configure the satellites and DTTs, you can't set the manual scan, with other softs it works if you do it right, with Egami yes and ' forced to set Sat and Dtt and then restart the box and then you can do personalized tuning.... it has had this defect for a long time.

I have another suggestion for those who use Egami. I have H7 and tested yesterday the bin of oscam samur is not functional, the one of the feed replaced it with one that works. I have the files that go in tuxbox/config fixed without changing them and replacing the bin the one I have enables immediately, the one of the feed is not enabled to save in the HTTP protocol:.

Greetings.

It's not about doing personalized tuning (but maybe I'm wrong somewhere), it's about that after finding the stations on both tuners B+C I can only watch the programs on tuner B (cable). I can switch to tuner C (terrestrial) I see the list of stations but I can't watch them. I hope I made myself understood. I can do another clean installation, if you want to help me, please give me the steps.

ThanksScreenshot 2024-11-20 121348.png

Screenshot 2024-11-20 121657.png

Screenshot 2024-11-20 122046.png

there is one thing that... tuner C is for cable... and if they are encoded channels....?? and if they are in Free on DTT you have to deactivate emu (oscam) try, for example I have the Ci+Plus for Tvsat with the Cam+card... if I leave oscam active I have no vision if instead I deactivate oscam the Ci+Plus works perfectly, you can't have 2 things at the same time.

Screenshot_20241122-115556~3.png

This happens even without having OSCAM installed or turned on. I have DVBT on tuner C, but when I want to access the tuner and implicitly the stations (the station in the picture is free), it appears as you can see in the pictures as if I don't have tuner C. I'm doing a clean install again, how do you suggest I do the tuner configuration settings?

Screenshot 2024-11-20 121348.png

Screenshot 2024-11-20 121657.png

hi, I don't use the C= via Cable that is working near me (Switzerland) but once you have set the C voice you should know which channel or transponder you would like to have and do the personalized search it is just a test to have proof that you have the source, then certain tuners behind the box there is a little button to activate DTT that increases the voltage to 5v.... try.

My configuration is this.

Zgemma H7C receiver, tuner A =Sat Multifeed, tuner B =DVBC cable Digi Romania, tuner C =DVBT terrestrial Mindig Tv Hungary.

This configuration works perfectly on OpenPli, OpenVix, OpenBh I don't have the problems described above. Until Egami I have this problem with OpenAtv, I can live with it but it annoys me and annoys me that I can't get rid of it. So you should check the situation with someone who has the same connections on tuners B and C, that is, B=DVBC connection and C=DVBT connection.

Thank you very much for your help.

ok,...I can't test I have H7s and I should go to Switzerland to test, if you have some time at your risk the box could block, go with the other software that works for you....that has the correct Drivers....save the lib/ folder of the soft inside there are the Drivers for sat and c (be careful this should not be done) but I always take risks with my boxes I have several, inside that folder if you search there is one with the name driver it should be replaced with that and restart the box but from the power if you are lucky it works if not you will have to restore everything...Attention it is only for experts.

It's not worth the risk, if I want all 3 tuners to work I change the image to multiboot, besides Egami I also have Openpli, Openbh and Openatv..

Hello, in the egami 10.6 image, the egami multiboot plugin has been removed, please add it.

Quote from piterfree

t Drivers....save the lib/ folder of the soft inside there are the Drivers for sat and c (be careful this should not be done) but I always take risks with my boxes I have several, inside that folder if you search there is one with the name driver it should be replaced with that and restart the box but from the power if you are lucky it works if not you will have to restore everything...Attention it is only for experts.

I saved the lib/folder Egami and OpenPli, where do I find the drivers for sat and c. I want to see where it's different?

IMG_20241122_155752~2.jpg

driver...!! Egami 10.6 R1

IMG_20241122_155327.jpg

IMG_20241122_155337.jpg

IMG_20241122_155346.jpg

IMG_20241122_155357.jpg

IMG_20241122_155406.jpg

IMG_20241122_155247.jpg

Thanks

I tried, I replaced the DRIVERS folder from OpenPli in lib/modules/4.10.12/kernel/drivers in Egami. The same thing, tuner C gives an error. The question would be. Why is everything OK on other images and on Egami which is a more dedicated image for Zgemma my configuration doesn't work? Sorry if I bored you!!!

2 test

Screenshot_20241122-220243~3.png

the ones I marked in red are the tuners for the C you have to select one at a time to test which one works for you.