Team
Having a sf8008 and it runs into network issues Are there any known network driver issues for this box?
I can only get 1000baseT/Full network speed on openatv 7.3
When running iperf3 test Its shows the perfect output
root@sf8008:~# iperf3 -c 10.66.77.14 -R ->>>> openATV 7.3
Connecting to host 10.66.77.14, port 5201
Reverse mode, remote host 10.66.77.14 is sending
[ 5] local 10.66.77.111 port 38916 connected to 10.66.77.14 port 5201
[ ID] Interval Transfer Bitrate
[ 5] 0.00-1.00 sec 112 MBytes 942 Mbits/sec
[ 5] 1.00-2.00 sec 112 MBytes 942 Mbits/sec
[ 5] 2.00-3.00 sec 112 MBytes 942 Mbits/sec
[ 5] 3.00-4.00 sec 112 MBytes 942 Mbits/sec
[ 5] 4.00-5.00 sec 112 MBytes 942 Mbits/sec
[ 5] 5.00-6.00 sec 112 MBytes 942 Mbits/sec
[ 5] 6.00-7.00 sec 112 MBytes 942 Mbits/sec
[ 5] 7.00-8.00 sec 112 MBytes 942 Mbits/sec
[ 5] 8.00-9.00 sec 112 MBytes 942 Mbits/sec
[ 5] 9.00-10.00 sec 112 MBytes 942 Mbits/sec
- - - - - - - - - - - - - - - - - - - - - - - - -
root@sf8008:~# ethtool -i eth0
driver: higmac driver
version: higmac v200
firmware-version:
expansion-rom-version:
bus-info: platform
supports-statistics: no
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
Settings for eth0:
Supported ports: [ TP AUI BNC MII FIBRE ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: Symmetric Receive-only
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Port: MII
PHYAD: 3
Transceiver: external
Auto-negotiation: on
Supports Wake-on: ug
Wake-on: d
Current message level: 0x00000007 (7)
drv probe link
When doing the same test on latest builds of opnVix OpenPli or openAtv i get a bad result
On OpenAtv 7.5.1
root@sf8008:~# iperf3 -c 10.66.77.14
Connecting to host 10.66.77.14, port 5201
[ 5] local 10.66.77.111 port 48322 connected to 10.66.77.14 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 256 KBytes 2.09 Mbits/sec 34 2.85 KBytes
[ 5] 1.00-2.00 sec 0.00 Bytes 0.00 bits/sec 2 1.43 KBytes
[ 5] 2.00-3.00 sec 0.00 Bytes 0.00 bits/sec 1 1.43 KBytes
[ 5] 3.00-4.00 sec 0.00 Bytes 0.00 bits/sec 5 4.28 KBytes
[ 5] 4.00-5.00 sec 128 KBytes 1.05 Mbits/sec 18 2.85 KBytes
[ 5] 5.00-6.00 sec 128 KBytes 1.05 Mbits/sec 13 2.85 KBytes
[ 5] 6.00-7.00 sec 0.00 Bytes 0.00 bits/sec 2 2.85 KBytes
[ 5] 7.00-8.00 sec 128 KBytes 1.05 Mbits/sec 21 5.70 KBytes
[ 5] 8.00-9.00 sec 256 KBytes 2.10 Mbits/sec 19 2.85 KBytes
[ 5] 9.00-10.00 sec 256 KBytes 2.10 Mbits/sec 18 4.28 KBytes
- - - - - - - - - - - - - - - - - - - - - - - - -
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 1.12 MBytes 944 Kbits/sec 133 sender
[ 5] 0.00-10.03 sec 1.12 MBytes 941 Kbits/sec receiver
When i force 100full with -> ethtool -s eth0 speed 100 duplex full autoneg off i get smooth 100mbit speeds
root@sf8008:~# iperf3 -c 10.66.77.14
Connecting to host 10.66.77.14, port 5201
[ 5] local 10.66.77.111 port 48326 connected to 10.66.77.14 port 5201
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 10.6 MBytes 89.1 Mbits/sec 0 599 KBytes
[ 5] 1.00-2.00 sec 10.6 MBytes 89.1 Mbits/sec 0 1.08 MBytes
[ 5] 2.00-3.00 sec 9.88 MBytes 82.8 Mbits/sec 0 1.57 MBytes
[ 5] 3.00-4.00 sec 10.9 MBytes 91.2 Mbits/sec 0 2.01 MBytes
[ 5] 4.00-5.00 sec 10.4 MBytes 87.0 Mbits/sec 0 2.01 MBytes
[ 5] 5.00-6.00 sec 10.5 MBytes 88.1 Mbits/sec 0 2.01 MBytes
[ 5] 6.00-7.00 sec 10.1 MBytes 85.0 Mbits/sec 0 2.01 MBytes
[ 5] 7.00-8.00 sec 10.4 MBytes 87.0 Mbits/sec 0 2.01 MBytes
[ 5] 8.00-9.00 sec 10.2 MBytes 86.0 Mbits/sec 0 2.01 MBytes
[ 5] 9.00-10.00 sec 10.6 MBytes 89.1 Mbits/sec 0 2.01 MBytes
root@sf8008:~# ethtool -i eth0
driver: higmac driver
version: higmac v200
firmware-version:
expansion-rom-version:
bus-info: platform
supports-statistics: no
supports-test: no
supports-eeprom-access: no
supports-register-dump: no
supports-priv-flags: no
Whats going on here?
Pls advise
