Where can I get Wicard-TVSAT-mips? I googled it but couldn't find it. Where is it?
OpenPli 13.4 DM800se sim2.1& original ssl84d
- mrlu
- Thread is marked as Resolved.
-
-
Where can I get Wicard-TVSAT-mips? I googled it but couldn't find it. Where is it?
It doesn't exist... I'm the only one who did it, but remember that it's not automatic, the PAC hasn't been created... for the Wicard.
-
Where can I get Wicard-TVSAT-mips? I googled it but couldn't find it. Where is it?
It doesn't exist... I'm the only one who did it, but remember that it's not automatic, the PAC hasn't been created... for the Wicard.
How can I get and add Wicard-TVSAT-mips?
-
I just showed you how to send the files I attached the other day.
I took a photo for you, and you just have to send me the folders. Then go to each folder containing the files I posted and give them 755 rights.
Then I told you which decoder you use: original or clone.
I made the backup and I can post it. OK.
-
I've tortured you, don't judge me harshly.
I am using DreamBox 800HD SE with SIM210 bootloader 84 clone, OpenPLUS 13.4
If I understood correctly, I need to send you this file.[reader]1.txt[reader]2.txt[reader]3.txt[reader]4.txt[reader]5.txt[reader]6.txt[reader]7.txt[reader]8.txt[reader]9.txt[reader]10.txt
-
backup-openpli-13.4-dm800se-clone-20251129
Sim.2.10.oscam+wicard clone
-
backup-openpli-13.4-DM800SE-clone-20251129
Sim.2.10. Клон OSCAM+Wicard
https://mega.nz/file/V1AEmJzL#... fPrMic4jN7tSGQkgLAOBlqZeoI downloaded and unzipped the file. There are two image files. I need to flash it with one of them.Image 7.png
-
There's the software...2025-12-11-11h34m-dm800se.nfi
+ssl 84d...if it doesn't restart, the decoder must be sent with the COM port if it causes the crash. -
Finally, I found the Wicard-TVSAT-mips file, unzipped it, and copied the files from my computer to the corresponding receiver folders as you described.
etc > initd > softcam.wicard
ets > tuxbox > config > vicardd .config
usr > bin > wicardd
edited vicardd .config and added my sharing settings.
rebooted the receiver,
launched wicardd in the receiver, but the channels aren't opening.
Where's my mistake?
-
-
-
you need to check where you put the front reader card above or below
test via web...8888
-
you need to check where you put the front reader card above or below
test via web...8888
-
Good afternoon!
I'm annoying you with my stupidity.
I'm very grateful for the time you're giving me.
It looks like Wicardd isn't working.
If you don't mind, let's try setting up the oscam emu.
Where can I get the configuration files?
-
In post #26,
I've attached the backup
to send to DM 800se Clone Sim2.10
And you're still asking how to configure everything.
There are tons of TVsat configurations for Oscam available online.
-
God bless you.
I uploaded the backup.
In Wicardd, I only edited Wicardd.config and added my sharing settings.
In Oscam, I only edited the oscam.server file and added my sharing settings.
It still closes, but the channels won't open.
Is there anything else I need to do?
-
You just need to check the TVsat card reader to see if it's the right one.
With OSCAM, go online and check if it reads the card's ATR.
If it doesn't, change the reader.
Reader = 0
Reader = 1
If it reads ATR, it takes 2 minutes for it to update.
-
I inserted a switched off card into the rear reader and it has been stuck for 3 weeks, see the photos
-
Display More
You just need to check the TVsat card reader to see if it's the right one.
With OSCAM, go online and check if it reads the card's ATR.
If it doesn't, change the reader.
Reader = 0
Reader = 1
If it reads ATR, it takes 2 minutes for it to update.
Просто проверьте считыватель карт TVsat, чтобы понять, подходит ли он.
С OSCAM проверьте онлайн, читает ли он ATR карты.
Если нет — смените считывателя.
Читатель = 0
Читатель = 1
Если он читает ATR, обновление занимает 2 минуты.
My card doesn't work, I get sharing without a card.
-
hi guys, help me, I need an OpenPLi-dm800se clone to support constant.cw or Biss channels. in order for oscam to work properly and Anticascading to work, please help me
Participate now!
Don’t have an account yet? Register yourself now and be a part of our community!
