No connection to my cardreader

Hi
Soon i will get realy bananas, i have tried to configure my Linux pc-->Linux Klient 3.2.0-34-generic #53-Ubuntu SMP Thu Nov 15 10:49:02 UTC 2012 i686 i686 i386 GNU/Linux
and added 2 smargos frpm argolis.

When i'm running dmesg | grep ttyS i get this result

[    0.457488] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.593579] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[    0.651725] 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    0.734599] 00:0b: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A

when im running
pc/sc scanner i'm getting this result
Scanning present readers...
Waiting for the first reader...

It seams that i have no connection to my readers and i have been looking in the forum and found a lot of helpful things but still struggling with this issue
When i'm running dmesg i'm getting this result

2775.882662] ftdi_sio ttyUSB1: FTDI USB Serial Device converter now disconnected from ttyUSB1
[ 2775.882918] ftdi_sio 1-1.4:1.0: device disconnected
[ 2777.233613] usb 1-1.4: new full-speed USB device number 5 using uhci_hcd
[ 2777.361111] ftdi_sio 1-1.4:1.0: FTDI USB Serial Device converter detected
[ 2777.361388] usb 1-1.4: Detected FT232BM
[ 2777.361399] usb 1-1.4: Number of endpoints 2
[ 2777.361409] usb 1-1.4: Endpoint 1 MaxPacketSize 64
[ 2777.361417] usb 1-1.4: Endpoint 2 MaxPacketSize 64
[ 2777.361487] usb 1-1.4: Setting MaxPacketSize 64
[ 2777.362632] ftdi_sio ttyUSB1: Unable to read latency timer: -32
[ 2777.364411] usb 1-1.4: FTDI USB Serial Device converter now attached to ttyUSB1

I have aslo latency timer which i think is beacuse there is no or readers are not found.

When i'm running -->opensc-tool --reader 0 --atr i recieve the following
No smart card readers found

root@Klient:~# setserial -G /dev/ttyUSB0
/dev/ttyUSB0 uart unknown port 0x0000 irq 0 baud_base 24000000 spd_normal low_latency

//Please could any one help me to configure my linux so the readers are connecting to the USB

Viasat and Canal + --> which is C more after the exchange between canal+ towards c-more

Quote from master G

I have no idea which card is in each smargo, so i suggest you remove one smargo and run the lsusb command so you get the correct output for each smargo/card, then edit the [reader] device = accordingly..

Add your boxid = to [reader] for VIASAT..

Try these configs buddy, if you have further problems show us your oscam log so we can see where the issues are..

Code

####oscam.conf####




[global]
nice = -1
logfile = /usr/local/etc/oscam.log
clienttimeout = 5000
fallbacktimeout = 2500
clientmaxidle = 120
cachedelay = 120
bindwait = 120
resolvedelay = 30
serialreadertimeout = 1500
maxlogsize = 10
waitforcards = 1
preferlocalcards = 1
saveinithistory = 1
keepalive = 1




[webif]
httpport = 8888
httpuser = 
httppwd = 
httprefresh = 15
httphideidleclients = 0
httpallowed = 192.168.0.0 - 255.255.255.255
debug = 255




[newcamd]
key = 0102030405060708091011121314
port = 34000@0b00:000000;34001@093E:000000
keepalive = 1




####oscam.server####




[reader]
label = CANAALDIGITAAL
protocol = smartreader
device = 001:005
caid = 0b00
ident = 0b00:000000
EMMCache = 1,1,0
group = 1




[reader]
label = VIASAT
protocol = smartreader
device = 001:006
boxid = # add your converted boxkey here
caid = 093E
ident = 093E:000000
emmcache = 1,3,2
group = 2







####oscam.user####




[account]
user = linuxsat1
password = support1
group = 1
caid = 0b00
ident = 0b00:000000
au = CANAALDIGITAAL




[account]
user = linuxsat2
password = support2
group = 2
caid = 093E
ident = 093E:000000
au = VIASAT

Display More

Display More

I made this corrections as suggested but im still struggling with the reader connection and can not get out any info from the log since the readers are not "connected" if i start the oscam with the commando -->/usr/sbin/oscam -b i can find this info on the screen:
^@^@/usr/src/oscam/oscam-svn/oscam-config-reader.c^@^@ERROR: '%s' is unsupported reader protocol!
^@^@^@Configuration newcamd: Error in Key
^@^@^@^@Determined local mac address for mg-encrypted as %s^@Configuration reader: corrected label to %s
^@^@^@^@Configuration reader: Error in rsakey
^@^@Configuration reader: Error in ins7E
^@^@^@Configuration reader: Error in ins7E
^@^@/usr/src/oscam/oscam-svn/oscam-config-reader.c^@^@ERROR: '%s' is unsupported reader protocol!

Quote from master G

Which version of oscam are you using and does it come with smargo pcsc support ? If it doesn`t have pcsc support then upgrade oscam..

http://linuxsat-support.com/li…ntu-server.html#post52984

I would check that the Smargo is set up properly, http://linuxsat-support.com/li…l-smargo-smartreader.html..

Connect to the oscam webinterface and copy any errors you see..

Display More

I am running the latest oscam-->oscam-1.20-unstable_svn7944-x86_64-linux-gnu-ssl-libusb-pcsc
If i am running this commando-->proc/tty/driver/serial i am recieving-->
serinfo:1.0 driver revision:
0: uart:16550A port:000003F8 irq:4 tx:0 rx:0
1: uart:16550A port:000002F8 irq:3 tx:0 rx:0
And if im running this commando-->opensc-tool --list-readers
No smart card readers found.
And if im running this comando-->setserial -G /dev/ttyUSB0
/dev/ttyUSB0 uart unknown port 0x0000 irq 0 baud_base 24000000 spd_normal low_latency

Reader firmware version 1,3

Very confused, probably my brain or the Pc are f*cked up
More info i installed the oscam on my win pc and there is now problem with the reader, they are connected to the USB ports in a proper way and are identified in the oscam etc. but the only problem with that one is i cant use the computer since i'am using that one for my profession but at least i know that the readers are not f*cked up

I have connected to the webif through my dreambox which information is needed?
Reader?
Status from first screen?

By the way thanks a lot for all help so far:mrg:

I am giving up...cant use the webif, cant get in contact with my readers and are trying everything i can find in the forum and also with all other help i'm getting from the members. It must be the pc that is not working as it should do even if i have updated it with the latest kernels and version of Ubuntu with other words it's a disaster.
I will buy a new computer beacuse now i will through it out through the window next to me and i hope that Santa is not entering below the window.
I will start all over with the new one with window configuration.

Thanks a lot all of you who tried to help out, i will come back with new question when i'm up and running with the win pc.
Merry Christmas and Happy New Year

To keep you posted;
Santa was not under the window thank good for that, but the man next to me (onkel Bill G) was there ooooppppps.
I have already started my win pc to debug so i will be back rather soon with more tricky ques...............

2012/12/22 13:12:47 C111E8 r cd [mouse] Cannot open device: device/ttyS12
2012/12/22 13:13:47 C111E8 r cd [mouse] ERROR: Opening device device/ttyS12 (errno=2 No such file or directory)
2012/12/22 13:13:47 C111E8 r cd [mouse] Cannot open device: device/ttyS12
2012/12/22 13:13:47 C12DC0 r viasat [mouse] ERROR: Opening device dev/ttyS13 (errno=2 No such file or directory)
2012/12/22 13:13:47 C12DC0 r viasat [mouse] Cannot open device: dev/ttyS13
Reader log:
cd mouse 0 / 0 / 0 / 0 0 / 0 / 0 / 0 0 / 0 / 0 / 0 0 / 0 / 0 / 0 0 (0.00%) 0 (0.00%) 0 / 0 100 Edit Reader Show Entitlement Reset and reload Entitlement Write EMM Loadbalancer statistics Delete Reader
disable this reader viasat mouse 0 / 0 / 0 / 0 0 / 0 / 0 / 0 0 / 0 / 0 / 0 0 / 0 / 0 / 0 0 (0.00%) 0 (0.00%) 0 / 0 100

I see something strange here dev/ttyS13 i have the config dev/ttyUSB0 and 1 in my oscam but in the webif it says S12&13 hmmm?

Hmmm confused
If i log in via web if for the linux Pc which should be the server 192.168.1.3:9999 it fails but if remove :9999 it says it works but strange
It works!

This is the default web page for this server.

The web server software is running but no content has been added, yet

Therfore it was a little confused and not so little (Boxaren is a jerk
) probably beacuse of all the fiddeling with ........
Sorry for this mess......

Correct i was trying with both 9999 and 8888 but both is denied connection failed
To even be sure i checked and both ports is open in Ubuntu

Hi Guys
Ok now i have a new computer and installed the oscam in win environment, everything is up and running including the web if.
First are there anything needed to be added in the different settings like reader etc in the webif?
If i checking in the log i have the following errors, could you explain whats wrong?
2012/12/23 13:47:57 C1C348 r viasat [mouse] ERROR: Opening device dev/ttyS13 (errno=2 No such file or directory)
2012/12/23 13:47:57 C1C348 r viasat [mouse] Cannot open device: dev/ttyS13
2012/12/23 13:48:57 C1AB78 r cd [mouse] ERROR: Opening device device/ttyS12 (errno=2 No such file or directory)
0 s newcamd: Bind request failed (Address already in use), waiting another 55 seconds