Oscam error activating card using box key only. NAGRA, caid: 1815

There are 32 replies in this Thread which was already clicked 18,628 times. The last Post () by murphy1969.

    Here below is the output of RQCS....


    Starting Logical Slot 'Upper' [Users: 3]
    ------------------------------------------------------------------------------
    Device Path: /dev/ttyUSB0 | Listening Port: 10001
    ------------------------------------------------------------------------------


    Opening sci... Done
    Detecting card... Card present
    Resetting card... Done
    Identifying card type...
    Historical bytes: D N A S P 2 4 0 R e v 9 0 8
    44 4E ..... some more numbers here 30 38
    Card type: Nagra
    ROM Revision: 240
    EEPROM Revision: Rev908


    Configuring sci...
    SCI | Conv: Inverse | Baud Rate: 115200 | Stop Bits: 2 | Parity: Odd


    Slot custom parameters:
    box_key: my box key
    dt06_key_0d:
    cam_n:
    secondary_key:
    rsa_key:
    des_key: 0102030405060708091011121314


    Card start-up initialization...
    Using DT08 session negotiation method:
    Setting Field Size: Done
    Retrieving IRD serial number: irdserial
    Retrieving CAM serial number: camserial
    Retrieving System IDs: 0901,0903
    Retrieving CAM modulus (DT08): Done
    Starting Session Negotiation: Done
    Retrieving CAM challenge data: Done
    Performing Session Key Negotiation: Successful


    Starting card worker thread... Done
    Starting protocol server on port 10001 [newcamd protocol]


    Logical Slot 'Upper' READY!
    ------------------------------------------------------------------------------


    Staring web interface: Done.

    Ok oscam is seeing more of your card now but still looking for a valid rsa key



    What version of rqcs are you using and can you check your rqcs.conf for a rsa key or cam_n key if you got help to set it up previously


    rqcs session negotiation says the card uses DT08 method for pairing

    The cam serial key shows when I run rqcs. RQCS version 1.11
    here is my rqcs config.
    ###############################################################################
    # rqcs configuration file #
    # All configuration options in this file observe the same format: #
    # <configuration_name>=<configuration_value> #
    # #
    # No white space is allowed in any place or the configuration entry will be #
    # ignored. #
    ###############################################################################


    ########################### general configuration #############################
    [General]
    box_type=3
    background_execution=1
    debug_level=1
    debug_show_ecms=1
    debug_show_emms=1
    log_to_console=1
    log_to_webif=1
    log_to_file=1
    logfile_name=/usr/local/bin/rqcs.log
    webif=1
    webif_port=665
    webif_authenticate=1
    webif_users=root:test
    webif_custom_files_root=
    system_wide_hour_offset=0


    ###############################################################################
    [Logical-Slot:Upper]
    enabled=1
    sci_type=1
    sci_ordinal=
    sci_path_custom=/dev/ttyUSB0
    sci_clock_frequency=367000
    safety_restart_period=20
    restart_on_ecm_send_error=1
    restart_on_ecm_processing_timeout=1
    restart_on_cw_retrieval_error=1
    restart_on_cam_request=1
    restart_on_emm_send_error=1
    restart_on_emm_processing_timeout=1
    maximum_ecm_rate=0
    block_emm_g=0
    block_emm_s=0
    block_emm_u=0
    allow_sids=
    deny_sids=
    send_card_tiers=1
    cache_card_tiers=1
    emm_log_file_path=rqcs-emm-log-upper.emm
    emm_log_file_max_size=512
    log_emm_g=1
    log_emm_s=1
    log_emm_u=1
    report_caid=0
    box_key=this is my box key
    dt06_key_0d=
    cam_n=
    secondary_key=
    rsa_key=
    protocol_server_type=0
    protocol_server_port=10001
    protocol_server_newcamd_des_key=0102030405060708091011121314
    protocol_server_user_file=rqcs.user
    protocol_server_max_active_users=0
    protocol_server_idle_client_timeout=30
    nagra_command_lead_time=25
    nagra_ecm_status_poll=1
    nagra_ecm_initial_poll_delay=0
    nagra_ecm_poll_delay=0
    nagra_ecm_poll_delay_increment=0
    nagra_emm_status_poll=1
    nagra_emm_poll_delay=100

    The only way you are going to get OSCam to decrypt this card is to get both the Boxkey and the RSAkey. If it opens using RQCS you are going to have to continue to use that until you get the RSAKey.


    Why is it so important that you use OSCam?


    If you have to use OSCam just put the card in another box running RQCS and then send an N line to the box running OSCam.

    rqcs says it's DT08 so oscam is probably looking for a valid rsa or at the very least a cam_n for session negotiation
    As nano has said you will probably need to use a valid rsa


    btw rqcs to oscam could be a non runner, ive seen someone try and fail
    rqcs runs just fine, so as asked why oscam ?

    If you send an N line from RQCS there is no reason why OSCam shouldn't be able to use, although this is only theory as i've never seen it done before.


    The other alternative is to send an N line to CCCam and use that instead.


    Nano

OSCam Support Forum

Configs, discussion, downloads and guides for OSCam Softcam.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login