Preparation and installation of firmware to USB - step by step

wrote: zukon

Quote

Preparation and installation of firmware to USB - step by stepThe following tutorial on how to prepare step by step and install any soft on USB or HDD1 - install the NAND / FLASH POINT latest version of the firmware - as of today it is NEBULA NEBULA v3 or ZERO and boot from NAND / FLASH2 - to a USB port hook pendraka best about 4GB - for BSLA or BSKA hard disk drive will be seen as sdb - if there is no hard disk is sda we operate in!3 - blue / yellow / blue call Disk Manager and prepare the USB using the following formula:

- My suggestion - set the first partition as vfat (more on that later)- Partitions 2-5 set after about 256MB ext2- 6 to set the partition as SWAP - 128MB should be enough- 7 to partition the remaining free space4 - save your partitions by pressing the yellow5 - go to the Mount Manager (for the record: blue / green / HDD Manager) and zamountować disks according to the formula- As / hdd give final partition USB - this file or files to be installed CrossEPG will drive wybudzał- A point mountowania 2 we drive on which record- A point mountowania 9 we first partition of the USB - it is a FAT partition to upload to NAND / Flash software without having to replace pendraka

5 - zamountować drives green
6 - via FTP to / hdd copy the image to be installed in *. Tar.gz intended for installation on SATA / USB
7 - get out and call the Install Manager - Blue / Yellow

up and down arrows select the image to be installed, right-left partition on which you want to install (IMPORTANT NOTE - sdb4 partition is a logical partition - for it is sdb5-8 - Never install a partition sdb4!)- Install by pressing red- With more softami proceed in the same - there are partitions sdb2, sdb3, sdb5, sdb68 - DONE!Now a few tricks:- As Point9 in / media is the mount of vfat partition - so we can FTP to copy the files to update, rootfs.img and uImage, when you reboot your box arrows select USB UPDATE, and we have installed soft! if you will not want to move it updated for the first time to format the partition for windows and I will work- As Point2 directory / media is already-mounted drive for recording - this will be nicely falling asleep. Changes track record we can make either / etc/enigma2/settings

Code

config.movielist.videodirs=['/media/Point2/movie/']
config.movielist.last_timer_videodir=/media/Point2/movie/
config.movielist.last_videodir=/media/Point2/movie/

or the remote control MENU (OPT) / configuration / system / HDD / track recording - choose: the default location / MENU (OPT) / switch to the list of files / Internal flash/media/Point2 highlight the movie and press the green (same can be followed for the timeshift)- Env for example BSLA of the drive and prepared according to the above formula pendrakiem:

Code

set bootdesc_0 'HDD2            '
set bootcmd_0 'set bootdesc_default 0; saveenv; run bootargs_0; run bootkern_0'
set bootkern_0 'ide reset; ext2load ide 0:2 a5000000 /boot/uImage; bootm a5000000'
set bootargs_0 "set bootargs console=ttyAS0,115200 root=/dev/sda2 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x100
00000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit";
set bootdesc_1 'HDD3            '
set bootcmd_1 'set bootdesc_default 1; saveenv; run bootargs_1; run bootkern_1'
set bootkern_1 'ide reset; ext2load ide 0:3 a5000000 /boot/uImage; bootm a5000000'
set bootargs_1 "set bootargs console=ttyAS0,115200 root=/dev/sda3 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x100
00000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit";
set bootdesc_2 'HDD5            '
set bootcmd_2 'set bootdesc_default 2; saveenv; run bootargs_2; run bootkern_2'
set bootkern_2 'ide reset; ext2load ide 0:5 a5000000 /boot/uImage; bootm a5000000'
set bootargs_2 "set bootargs console=ttyAS0,115200 root=/dev/sda5 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x100
00000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit";
set bootdesc_3 'USB2            '
set bootcmd_3 'set bootdesc_default 3; saveenv; run bootargs_3; run bootkern_3'
set bootkern_3 'usb reset; ext2load usb 0:2 a5000000 /boot/uImage; bootm a5000000'
set bootargs_3 "set bootargs console=ttyAS0,115200 root=/dev/sdb2 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x100
00000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit";
set bootdesc_4 'USB3            '
set bootcmd_4 'set bootdesc_default 4; saveenv; run bootargs_4; run bootkern_4'
set bootkern_4 'usb reset; ext2load usb 0:3 a5000000 /boot/uImage; bootm a5000000'
set bootargs_4 "set bootargs console=ttyAS0,115200 root=/dev/sdb3 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x100
00000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit";
set bootdesc_5 'USB5            '
set bootcmd_5 'set bootdesc_default 5; saveenv; run bootargs_5; run bootkern_5'
set bootkern_5 'usb reset; ext2load usb 0:5 a5000000 /boot/uImage; bootm a5000000'
set bootargs_5 "set bootargs console=ttyAS0,115200 root=/dev/sdb5 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x100
00000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit";
set bootdesc_6 'USB6            '
set bootcmd_6 'set bootdesc_default 6; saveenv; run bootargs_6; run bootkern_6'
set bootkern_6 'usb reset; ext2load usb 0:6 a5000000 /boot/uImage; bootm a5000000'
set bootargs_6 "set bootargs console=ttyAS0,115200 root=/dev/sdb6 rw ip=$ipaddr:$gatewayip:$serverip:$netmask:eth0:off mem=128m coprocessor_mem=4m@0x100
00000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit";
set bootdesc_7 'NAND B4Team     '
set bootcmd_7 'set bootdesc_default 7; saveenv; run bootargs_7; run bootkern_7'
set bootkern_7 'nand read.i 0xa5000000 0x0 0x300000; bootm a5000000'
set bootargs_7 "set bootargs console=ttyAS0,115200 root=/dev/mtdblock3 rw rootfstype=jffs2 ip=$ipaddr:$gateway:$serverip:$netmask:eth0:off mem=128m copr
ocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin/devinit";
set bootdesc_8 'NAND Lamer      '
set bootcmd_8 'set bootdesc_default 8; saveenv; run bootargs_8; run bootkern_8'
set bootkern_8 'nand read.i 0xa5000000 0x3c00000 0x300000; bootm a5000000'
set bootargs_8 "set bootargs console=ttyAS0,115200 root=/dev/mtdblock0 rw rootfstype=jffs2 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 nwhwconf
=device:eth0,hwaddr:$ethaddr init=/bin/devinit";
set bootdesc_9 'UPDATE USB      '
set bootcmd_9 'run bootkern_9'
set bootkern_9 'usb reset; fatload usb 0:1 a4000000 update; autoscr'
set bootcmd 'bootmenu'
set bootdesc_items 9;
set bootmenutimeout 5;

Display More

- It can be successfully applied to other boxes - for sure it will work on IPBox 9900/99/55.

Display More