Full manual update Amiko
(Client) for the 1st time (firmware, channel list and server)
Good friends!
This I'm posting here is already scattered around in various threads I think,
But what I pertendo is that a manual be only a basic explanation of how to put
Amiko one (client) that are numerous different models except the Spark, Enigma2 operating
since sending the 1st firmware as well as the channel list and will he not leave the lin to be attached thereto ***
So after this little presentation so let's get to it!!
Borá there!
How have the new box or it does not come with list of channels that pertendemos
As also does not come with the firmware with their emulators
(Explanation in this case to work for CCcam) for us metermos its fruit,,,, ok fine!
Come on then put the firmware to have access to their emulators (CCcam).
Important! Whenever we make a complete connection of a box (net and signal cable satellite or cable, etc etc,,,)
we have to take into account that 1 bind all cables and last is that we turn on the box to the mains,,,
when we turn off the box and their cables do the reverse
1st off box chain cables after then, never instead, ok??
Since we already have a box connected c'mon then send the firmware!!
1 We here in the forum section of Amiko and we will search for the firmware for the model
our Amiko should have for sure (if you are not open help topic to the same application)
2 Since we already have the firmware will send the miscreant back inside the box,, ok?
HOW TO SEND THE FIRMWARE
1st Come format a usb stick in fat 32 and come get their file ABS
Just the same file, nothing more, nor RAR or folders or anything, just the same file
Phew! The guy is boring,,,,, ok! I know it's only the file,,,,
2 Let us now put the usb stick containing the firmware file in the box
And we will follow these steps,,,,,,,,,,,,,
SEND FIRMWARE
1 MENU
2nd SYSTEM
3 UPGRADE BY USB,,,
4th UPDATE FILE (here we only see if in fact the file we want to send is being recognized by the box)
ok well the box is recognizing the file,,,,,,
5 Let the update mode and will choose allcode BOTTLOADER +,,,,,
here there is no doubt we will then initiate the shipping firmware,,,,,
6 we click START or START comforme is described in your box,
but I think it is STARTED,,,
7 The box will start loading the firmware in which we will see in a chart the evolution
sending when reach the end they do not move at all because the box will reboot and goes back to its normal state,
VERY CAREFULLY! DURING SHIPPING SO DO NOT touch their COMMAND
HOW NOT take A PEN OR disconnect the USB BOX CHAIN
Also turn off the microwave, do not go sometimes electricity go down
I'm serious, ok??? If you think that the picture is very charged send the firmware
at a time when fewer appliances are connected to the mains,,,,,
Very well! We already have the firmware now we send the channel list!
We will do exactly as we did earlier if we already have the list very well!
Otherwise go to the forum and look for the list compatible with the model of our box
Or, as I mentioned earlier to request help for the list of channels,
SEND CHANNEL LIST
Friends is now very simple,,,,, as we know now we will send the firmware do exactly
all steps such as sending firmware only now in MODE UPDATE
we choose as there was no longer to be (CHANNEL LIST) obvious!!
And the box will have exactly the same symptoms you had in sending the firmware
Will load and restart,,,,, if all goes well there already live channel list!!
Ok my friends, we have prepared the ground for the garden now lack the most important
Their flowers,,,,,, for this we will have to have the same place in the garden,,,,,
HOW TO PUT THE ROW ***
1 MENU,,,,, / 2 INTERNET,,, / 3 CLIENT CS,,,,, Now this menu here is where we get their,,,,,, now come on!!
Suppose your lin ***, that's it??
C: xicomarreco.dyndns.org 12000 jonh scott (Note: this is just an example)
SERVER NAME,,,,,,,,,, Here lay the host of your server,,,,,, (xicomarreco.dyndns.org)
And keep with the red button,,,,,,,,,
DOOR,,,,,,,, Here put the number of the door,,,,,, (12000)
USER NAME,,,,,,, Here put your user which in this case (jonh), and keep with the red button
PASS,,,,, Here are put as regards the said line (Scott), and keep with the red button
DES KEYS,,,,, They leave and move on to be,,,,,
ACTIVE SERVER,,, Here are OK until the green dot into place
EMULATOR,,,,, this case will choose CCCAMD,,,,
Now that it is set let's click red button STORE
Friends! If the said active and are all well configured dolls emerge
Surely,,,,,,,,
Good friends! So give this little manual terminated
I also have a duty to inform you that this manual was based on a AMIKO MINI COMBO,,,,,
but now sent to over eighty amikos family,,,,, and also make sure to other
boxs not amikos with by exp º and other ORTON!!
Note: for questions use the forum, ok??
and already my apologies for something that has escaped,,,,
Moral of the story,,,,, I'm getting old!
Embrace this your friend!
bertinho
obs: sorry as I am Portuguese had to use google translator