Oscam not using local card.

There are 5 replies in this Thread which was already clicked 4,437 times. The last Post () by nd01mtm.

    Hi all,


    I am relatively new to Oscam and have recently migrated from CCcam. My current setup is Oscam 1.00/Cccam 2.1.3 and is working great except when I change channels it is not using Local but instead uses remote card. Initially it uses the local when rebooted but after an hour or so it uses remote again. Another issue which i believe to be connected is the high ecm time when zapping when using remote card.


    I have tried the prefer local card = 1 in oscam config but this does not help.


    Hope i can get some help here and thanks in advance


    Dreamal

    You havent given much info here as regards what you are using equipment wise , you need to post configs etc , if you are using a usb reader on a pc try run it thru a powered usb hub to speed times up and make sure your local and remote are different groups , this is a shot in the dark at what your issue may be as your info is insufficient

    Ya some info would be handy alright I guess....


    My Server is a DM500 SD running Gemini, Oscam 1.00 CCcam2.13 with local s** 963 card. Configs posted below


    Overview of problem: When server is started it uses local but after an hour or so it reverts to using remote cards when zapping. As my server is running 24/7 Im taking unnecessary Ecms from peers.
    Any solution would be appreciated..... Thanks


    Oscam.config


    [global]
    logfile = /var/local/oscam.log
    clientmaxidle = 9000
    cachedelay = 120
    unlockparental = 1
    nice = 4
    maxlogsize = 100
    preferlocalcards = 1
    saveinithistory = 1
    lb_mode = 1
    waitforcards = 0


    [newcamd]
    port = XXXXX@0963:000000
    key = 0102030405060708091011121314
    keepalive = 1



    [webif]
    httpport = XXXX
    httpuser = XXXXX
    httppwd = XXXXXXXX
    httprefresh = 10
    httpallowed = 127.0.0.1,192.168.0.0-192.168.255.255


    Oscam.server


    [reader]
    label = mouse
    enable = 1
    protocol = internal
    device = /dev/sci0
    caid = 0963
    fix9993 = 0
    detect = cd
    mhz = 600
    cardmhz = 357
    ident = 0963:000000
    group = 1
    emmcache = 1,3,2
    blockemm-unknown = 1
    blockemm-g = 1
    lb_weight = 100


    Oscam.user


    [account]
    user = xxxxxxxx
    pwd = xxxxxxxx
    uniq = 2
    monlevel = 1
    caid = 0963
    ident = 0963:000000
    group = 1
    au = 1
    keepalive = 1

    Can anybody help with this problem.?


    Your support would be appreciated as i am new to oscam and i am at a loss to what the issue may be...:20_003:

    Im running oscam and mgcam.
    In oscamserver and [newcamd] i write mgclient=1.
    Same for cccam? Need to define your clients?

    Dreambox 800HDSE clone, E2 4.6, cccam, oscam

  • master G

    Set the Label from UK OSCam to Videoguard2 Cards OSCam

OSCam Support Forum

Configs, discussion, downloads and guides for OSCam Softcam.

Participate now!

Don’t have an account yet? Register yourself now and be a part of our community!

Register Yourself Login