Problem with card reader 3121 omnikey

Running oscam on ubuntu 13.10 and have new card readers that I do not get to work.

This reader

root@ubuntu:~# sudo lsusb
Bus 002 Device 002: ID 058f:6361 Alcor Micro Corp. Multimedia Card Reader
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 002: ID 076b:3022 OmniKey AG
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 076b:3022 OmniKey AG
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

USB Devices
Bus 002 Device 002: ID 058f:6361 Alcor Micro Corp. Multimedia Card Reader
iProduct 2 Mass Storage Device
iSerial 3 058F63616476
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:1d.7
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.2
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.1
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1d.0
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
iProduct 2 EHCI Host Controller
iSerial 1 0000:00:1a.7
Bus 005 Device 002: ID 076b:3022 OmniKey AG
iProduct 2 Smart Card Reader USB
iSerial 0
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
iProduct 2 UHCI Host Controller
iSerial 1 0000:00:1a.2
Bus 004 Device 002: ID 076b:3022 OmniKey AG
iProduct 2 Smart Card Reader USB
iSerial 0

[reader]
label = canaldigital
protocol = pcsc
device = 0
caid = 0B00
detect = cd
ident = 0B00:000000
group = 1
emmcache = 1,3,2
blockemm-unknown = 1
blockemm-u = 1
blockemm-g = 1

log:
2015/01/22 17:56:06 0 s waiting for local card init
2015/01/22 17:56:06 1BC5860 r canaldigital [pcsc] Cannot open device: 0

oscam closes down after a while, what could be wrong??

Quote from superkazza

I think your device needs to be labeled correctly Not 0. One of the Guy's with more knowledge with say for sure
Have a look here:
http://linuxsat-support.com/showthread.php?t=1712
Or if you have simplebuild installed:
http://linuxsat-support.com/showthread.php?t=30959

I can not find this in the file: reader_drivers = pcsc, ctapi;

- - - Updated - - -

and simple build I have allready installed as you links to!

Quote from mckee25

I have attached an edited opensc file for you..... this is tried & tested using two omnikey readers.

I took a new clean install of ubuntu 13.10 64-bit and uses only one reader.
and I've run the script for autoinstall of CCcam / oscam.
Have used your file but keep getting no readers!

2015/01/23 11:11:23 440008C0 h canaldigital [pcsc] Restarting reader
2015/01/23 11:11:23 440008C0 h canaldigital [pcsc] creating thread for device 0
2015/01/23 11:11:23 48003B40 r canaldigital [pcsc] Cannot open device: 0

I run this:
Code:
opensc-tool list-readers

only get this:
root@playlive:~# opensc-tool list-readers
Usage: opensc-tool [OPTIONS]
Options:
-i, --info Prints information about OpenSC
-a, --atr Prints the ATR bytes of the card
--serial Prints the card serial number
-n, --name Identify the card and print its name
-G, --get-conf-entry <arg> Get configuration key, format: section:name:key
-S, --set-conf-entry <arg> Set configuration key, format: section:name:key:value
-l, --list-readers Lists readers
-D, --list-drivers Lists all installed card drivers
-f, --list-files Recursively lists files stored on card
-s, --send-apdu <arg> Sends an APDU in format AA:BB:CC:DD:EE:FF...
-r, --reader <arg> Uses reader number <arg> [0]
-c, --card-driver <arg> Forces the use of driver <arg> [auto-detect]
--list-algorithms Lists algorithms supported by card
-w, --wait Wait for a card to be inserted
-v, --verbose Verbose operation. Use several times to enable debug output.

I think I'm missing something in ubuntu?

I have some old readers who works just fine (ID 076b:3021 OmniKey AG CardMan 3121)
but the new will not work (ID 076b:3022 OmniKey AG)

- - - Updated - - -

Figured a little more now, found out by comando:

root@playlive:~# opensc-tool -l
No smart card readers found.

root@playlive:~# opensc-tool -D
Configured card drivers:
cardos Siemens CardOS
flex Schlumberger Multiflex/Cryptoflex
cyberflex Schlumberger Cyberflex
gpk Gemplus GPK
gemsafeV1 driver for the Gemplus GemSAFE V1 applet
miocos MioCOS 1.1
mcrd MICARDO 2.1 / EstEID 1.0 - 3.0
asepcos Athena ASEPCOS
starcos STARCOS SPK 2.3/2.4
tcos TCOS 3.0
openpgp OpenPGP card
jcop JCOP cards with BlueZ PKCS#15 applet
oberthur Oberthur AuthentIC.v2/CosmopolIC.v4
authentic Oberthur AuthentIC v3.1
iasecc IAS-ECC
belpic Belpic cards
ias IAS
incrypto34 Incard Incripto34
acos5 ACS ACOS5 card
akis TUBITAK UEKAE AKIS
entersafe entersafe
epass2003 epass2003
rutoken Rutoken driver
rutoken_ecp Rutoken ECP driver
westcos WESTCOS compatible cards
myeid MyEID cards with PKCS#15 applet
sc-hsm SmartCard-HSM
setcos Setec cards
muscle MuscleApplet
atrust-acos A-Trust ACOS cards
piv PIV-II for multiple cards
itacns Italian CNS
javacard JavaCard (without supported applet)
default Default driver for unknown cards