hi there,
My wetek doesn't start anymore.
When i try al recovery images nothing happends.
I will get black screen even when i try the 10 seconds recovery pin.
this is my putty.log
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.05.09 21:52:06 =~=~=~=~=~=~=~=~=~=~=~=
EEEE I3000000032940xf3001103 03;77520EEEE I400000004294_M6_BL1_3431 >2534313
TE : 77476
BT : 11:09:43 Mar 26 2015
CPU clock is 1200MHz
wait pll-0x03 target is 0204 now it is 0x00000203
DDR clock is 516MHz with Low Power & 2T mode
DDR training :
DX0DLLCR:40000000
DX0DQTR:ffffffff
DX0DQSTR:3db05001
DX1DLLCR:40000000
DX1DQTR:ffffffff
DX1DQSTR:3db05001
DX2DLLCR:40000000
DX2DQTR:ffffffff
DX2DQSTR:3db05001
DX3DLLCR:40000000
DX3DQTR:ffffffff
DX3DQSTR:3db05001
Stage 00 Result 00000000
Stage 01 Result 00000000
Stage 02 Result 00000000
Stage 03 Result 00000000
DDR init use : 42454 us
HHH
BootFrom SPI
ucl decompress
decompress true
0x12345678
Boot from int dev 1stSPI
TE : 1302929
System Started
U-boot(wetek@) (Mar 26 2015 - 11:09:29)
aml_rtc_init
aml rtc init first time!
clr h-ram
DRAM: 1 GiB
relocation Offset is: 105e0000
MMC: [mmc_register] add mmc dev_num=0, port=1, if_type=6
[mmc_register] add mmc dev_num=1, port=2, if_type=6
SDIO Port B: 0, SDIO Port C: 1
NAND: Amlogic nand flash uboot driver, Version U1.06.020 (c) 2010 Amlogic Inc.
SPI BOOT : continue i 0
No NAND device found!!!
NAND device id: 2c 44 44 4b a9 0
NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron D revision NAND 4GiB MT29F32G08CBADA)
1 NAND chips detected
#####aml_nand_init, with RB pins and chip->chip_delay:20
bus_cycle=5, bus_timing=6, start_cycle=6, end_cycle=7,system=5.0ns
oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH40_1K_MODE
aml_chip->oob_fill_cnt =168,aml_chip->oob_size =744,bch_bytes =70
multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
aml_nand_init:oobmul =1,chip->ecc.layout->oobfree[0].length=16,aml_chip->oob_size=744
aml nand env valid addr: 108000 ,status =0
key start_blk=2040,end_blk=2047,aml_nand_key_init:684
aml nand key valid addr: ff000000
aml nand key valid addr: ff200000
aml nand key valid addr: ff400000
aml nand key valid addr: ff600000
CONFIG_KEYSIZE=0x10000; KEYSIZE=0xfffc; bbt=0x1330; default_keyironment_size=0xeccc
i=0,register --- nand_key
NAND bbt detect Bad block at 0
Creating 8 MTD partitions on "nandnormal":
0x000000800000-0x000001000000 : "logo"
0x000001000000-0x000001800000 : "aml_logo"
0x000001800000-0x000002000000 : "recovery"
0x000002000000-0x000002800000 : "boot"
0x000002800000-0x000042800000 : "system"
0x000042800000-0x000062800000 : "cache"
0x000062800000-0x000072800000 : "backup"
0x000072800000-0x0000ff000000 : "data"
nandnormal initialized ok
detect mx chiprevD :1 and nand_type: 40
nand_curr_device =1
SPI BOOT,spi_env_relocate_spec : env_relocate_spec 53
SF: Detected MX25L3205D with page size 256, total 4 MiB
SPI NOR Flash have write protect!!!
In: serial
Out: serial
Err: serial
register usb cfg[0][1] = 9fe85cf4
Net: Meson_Ethernet
init suspend firmware done. (ret:0)
Hit Enter key to stop autoboot -- : 5 4 3 2 1 0
exit abortboot: 0
Amlogic Ethernet Init
Success: reset mac OK!(0)
ETH PHY hardware reset OK
find net phy id=0x7c0f1, phyad=1
set_mac_mode(0)
final_addr[rx-tx]: 0x9feee000-0x9feee600
Ethernet reset OK
MAC address is e8:18:63:50:2f:b8
phy auto link failed
half duplex
10m
BOOTP broadcast 1
phy auto link failed
phy auto link failed
BOOTP broadcast 2
phy auto link failed
phy auto link failed
BOOTP broadcast 3
phy auto link failed
phy auto link failed
BOOTP broadcast 4
phy auto link failed
phy auto link failed
BOOTP broadcast 5
phy auto link failed
p
