Installation Manual OSCAM Official Firm 0.9.5306
I created this manual, for those who still are with the official firmware, you can have with your oscam in deco, activate the server cccam server and make compost from your sbox, obtained for all the fruit to view it and burn it to your deco with conf.
INSTALLATION OSCam_svn_build # 5352 in AZbox.
Requirement .- have a deco swap, 40-50 Mb
1 º. Download the attached zip and unzip on PC, get a folder called oscamCAS
2 º. Select the folder and transfer oscamCAS via FTP to AZbox in this directory /PLUGINS/OpenXCAS
* Once inside oscamCAS in deco, give permissions, all files to 644, except ccc_to_oscam and oscam, two to 755, as well oscamCAS folder to 755.
* Within the files:
-Oscam.conf
-Oscam.server
-Oscam.user
* Oscam.conf: we just have to edit this:
[Cccam]
port = PuertoCCcam
version = 2.1.4 # which use
updateInterval = 60
ignorereshare = 1
Reshare = 1
minimizecards = 0[Webif]
httpport = 83
httpuser = # this if you want to put a user webinterface
httppwd = # the pwd of the user of the webinterface
httprefresh = 60
httpallowed = 192.168.1.2-192.168.1.255 # range of devices mounted on your local network, so we will start the webinterface
httphideidleclients = 0
httpreadonly = 1 * oscam.conf everything else leave it as is.
* To configure files and oscam.user oscam.server we can use the script that is inside "ccc_to_oscam."
would only get your C, F and N in the file in the folder oscamCAS "CCcam.cfg" and run these commands:
cd /PLUGINS/OpenXCAS/oscamCAS/./ccc_to_oscam -nalso I have set in the configuration examples rar
with this we would have oscam.user oscam.server and configured with our data.
(Not recommend this, because according to the format makes the files, the server OSCAM this version, I controlled the traffic well and the end result crashed server, use the settings that I have left in the default oscam.server and oscam.user, so you you will avoid problems.) is just edit it directly with your FTP program, all parameters the same, just going by adding your data and adding blocks as you may have few readers and users, respectively.
* Other files within oscamCAS not touch it, those files once we put more in expert mode, you can edit them.
* We have module.seq cercionarmos oscamCAS that, we go to the "activation and priority setting" and start oscamCAS.
* Then reboot and look to OSCAM deco is torn, if everything went well OSCAM should be running if not start it you can see in telnet process entering its directory and running:
cd /PLUGINS/OpenXCAS/oscamCAS/./oscam
With a ps console and see if we have in process.
* For now comment # oscamCAS (activation and priority setting), then we will put in place.
*** We will implement the following configuration in AZbox. OSCAM MultiCAS + sbox + ***
Comments:
Using MultiCAS and Sbox is that the viewing and recording, the reader is not entirely OSCAM achieved.
* Prerequisite to use one of the latest versions of MultiCAS.
* Sbox read our card.
1, configuration sbox.
* Installation and configuration sbox, with a little info on the forum can have it running on your deco.
* Sbox user in putting two, one for the newcamd.cfg MultiCAS and one for OSCAM will go into the reader of Sbox of oscam.server
* Sbox the start, remember you have mentioned so far OSCAM. (If you already have installed before you start commenting MultiCAS Sbox). No other EMU can be activated on boot time sbox.
2 º MultiCAS Settings:
* Install MultiCAS.
* We will use to connect to newcamd connection OSCAM.
* Rename the file newcamd.cfg example-folder which is inside MultiCAS, we will call newcamd.cfg
* We will enter into newcamd.cfg and we will delete the content that comes by default, we will use nlines allowed, ie a total of 12.
* This is the format and we will leave within newcamd.cfg, you have to put 12 more so, one for each fall / providing that you use regularly, and we have to turn in oscam.conf, which will see in the oscam.conf are those that usually use, change it to your needs:
Code:
N: 127.0.0.1 usersbox pwdsbox 30001 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 127.0.0.1 multicas pwdmulticas 30002 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 127.0.0.1 multicas pwdmulticas 30003 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 127.0.0.1 multicas pwdmulticas 30004 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 127.0.0.1 multicas pwdmulticas 30005 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 127.0.0.1 multicas pwdmulticas 30006 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 127.0.0.1 multicas pwdmulticas 30007 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 127.0.0.1 multicas pwdmulticas 30008 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 127.0.0.1 multicas pwdmulticas 30009 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 127.0.0.1 multicas pwdmulticas 30010 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 127.0.0.1 multicas pwdmulticas 30011 01 02 03 04 05 06 07 08 09 10 11 12 13 14
N: 127.0.0.1 multicas pwdmulticas 30012 01 02 03 04 05 06 07 08 09 10 11 12 13 14*store.
* May use the protocol CCcam with MultiCAS (I recommend the newcamd), only one would be to CCcam.cfg cline type: C: pwd ipdeco user port. or even both protocols.
* Edited newcamd.cfg once we enter to the menu command plugins within MultiCAS in newcamd-client, loaded with the blue button released, we all options enabled, login, emms, keep red. We go out and say connect "yes". Look in the module.seq ARE the three in this order, multicenter oscamCAS-SboxCAS.
* Now if we remove pad to oscamCAS (activation and priority setting) and we restart deco.
*** If everything is configured correctly, we will take our receiver running Sbox MultiCAS + + OSCAM ***.
*** This version I have been testing a few days and doing quite well, if you want to change it, the paradise and the binary meteis wish .***
Enjoy it!
