Posts by alhaiki
-
-
Hello Ahmed,
very beautiful image for my SF 8008, but 1 problem: not install Ncam (in Openbh 4.4. no problem, Oscam no problem), thanks and CIAO
opkg install --force-overwrite http://ipkinstall.ath.cx/ipk-i…ccam-images_2.3.9_all.ipk
opkg install --force-overwrite http://ipkinstall.ath.cx/ipk-i…cams-ncam_12.4-r0_all.ipk
opkg install --force-overwrite http://ipkinstall.ath.cx/ipk-i…cams-oscam_11.703_all.ipk
opkg install --force-overwrite http://ipkinstall.ath.cx/ipk-i…cam-supcam_11.703_all.ipk
opkg install --force-overwrite http://ipkinstall.ath.cx/ipk-i…-ncam-supcam_12.4_all.ipk
opkg install --force-overwrite http://ipkinstall.ath.cx/ipk-i…cam-revcam_11.703_all.ipk
opkg install --force-overwrite http://ipkinstall.ath.cx/ipk-i…-ncam-revcam_12.4_all.ipk
opkg install --force-overwrite http://ipkinstall.ath.cx/ipk-i…-oscam-tnt_11.678_all.ipk
opkg install --force-overwrite http://ipkinstall.ath.cx/ipk-i…cams-revcamv2_0.2_all.ipk
-
Mr. parageria serviceapp not in the feeds how can i install
-
how do I install 'INSTALL AS BACKUP'? Would you like to provide information about it?
thanks in advance
first you need to make sure that 'sim has your decoder, then follow this guide
1. Turn off the decoder from the switch on the back, in the absence of the latter, unplug the power cable from your Dreambox.
2. Press and hold the power button on the front panel of your decoder and turn the decoder back on.
3. Always keep the power button on the front panel pressed until *** STOP *** appears on the display together with the IP address of the decoder (eg 192.168.1.33).
4. Open your computer browser and enter the above IP address to access the firmware installation page.
5. At this point click on Firmware upgrade.
6. Send first the ssl (secondstage) then without closing, go back, and select the firmware to install, once selected click on the Flash button! to proceed with the installation of the new firmware. as soon as finished, do not reboot, and go back
WORKS only on multiboot
NFI ONLY FOR MULTIBOOT
INSTALL AS BACKUP
this original PLI image, dm8000, modified to work on dm800se sim2 84d
WORKS only on multiboot
NFI ONLY FOR MULTIBOOT
INSTALL AS BACKUP
FEEDS - ADDONS work
ONLINE UPDATE workDOWNLOAD
It works with excellence
-
how can i get Japhar sim i need 2 for my box dm800se v1 and v2
-
no information about this image ?
-
i need the image for dm800sev2 sim2.2 ssl88a with last vision openvision 10.2 can you make it please
-
what image use in intenal flash to boot this image in external flash
-
please try
User: root
Password: dreamboxChange your forgotten password:
Open OpenWebif with your IP 192.168.xxx.xx, then at the bottom left on Terminal, login: root, then for example openpli, enter passwd, then dreambox (you cannot see the entry dreambox) and again dreambox, or enter another password, Enter. Reboot completed.
Now you can access the receiver again via FTP >>> DCC / Filezilla
FTP User root ## FTP Password: openspa or openpli or openvix or openatv or your image name, or dreambox
i try but not change i dont know where is the problam
normally it has to work
please try this:
How to change your password using Dreambox Control Center>>DCC
Start DCC and ensure your network is ok and you have green lines to your router and Dreambox.
click on telnet tab then you get a black screen type on the screen login:
root
dreambox if default
then type>>>passwd
Ignore what it states about password length and enter a new password. any length.
be careful because you do not see any letters come on the screen. type the password then hit return and retype it again, then you will see password changed.
if you see the bad password: too weak. ignore it and retype the same as you did firstafter reboot
im using this image with my dm800se v2 in external hard disk and its work good only ftp my problam
-
please try
User: root
Password: dreamboxChange your forgotten password:
Open OpenWebif with your IP 192.168.xxx.xx, then at the bottom left on Terminal, login: root, then for example openpli, enter passwd, then dreambox (you cannot see the entry dreambox) and again dreambox, or enter another password, Enter. Reboot completed.
Now you can access the receiver again via FTP >>> DCC / Filezilla
FTP User root ## FTP Password: openspa or openpli or openvix or openatv or your image name, or dreambox
i try but not change i dont know where is the problam