Message 553 PY3.12 arm V1.0 working perfektly(OpenATV 7.5-devel) octagon sf8008.,Thanks Ziko.
Here too working fine on Octagon sf8008 OpenATV-7.5. Thanks Ziko.
Posts by Pete29871
-
-
Wishing you a very speedy and complete recovery. Get well soon.
-
Format a usb pen to FAT 32
Download this file openatv-7.4-sf8008-20240110_recovery_emmc.zip from the openatv forum.
Extract its contents to the pen (you should now have only 5 files on the pen drive
Insert the pen drive in the side usb port
Switch off the receiver, then on again whilst holding the power button on the receiver
until you see Updt. Then just let go the power button and wait until the box is fully flashed and booted to the new image which will also contain your Multiboot.
-
Yes, yours works fine. I must have done something wrong?
-
On Octagon sf8008 when trying to open Netflix Receiver jams, remote stops responding and only starts after GUI command.
Netflix works fine now on 7.5....thanks.
-
Thanks for your reply. I attach the relative bootlogo.jpg used.
-
Turned off Antivirus protection momentarily and now OK. Thanks.
-
Thank you for your script.
I have followed your instructions using Octagon sf8008 with OpenATV-7.4 and also on 7.5 Images.
The bootlogo.mvi file was duly created.
However, when transferred to usr/share, I could only see a very distorted bootlogo which was hardly visible.
The size of the bootlogo.mvi file created by the script was of 36,911 bytes.
On checking, my actual bootlogo.mvi file (which I usually use and corresponding to the same bootlogo.jpg file used in the script)
it shows a much larger size of 107,075 bytes.
Do I need to change some settings, please?
Thanks.
-
Hi. Tried to open the Octagon download link but got the following message:-
This site can’t provide a secure connection
http://www.nonsolosat.net sent an invalid response.
Turned off Antivirus protection momentarily and now OK. Thanks.
-
On Octagon sf8008 when trying to open Netflix Receiver jams, remote stops responding and only starts after GUI command.
-
On Octagon sf8008 with OpenPLI-9.0 works fine. Thks.
-
I confirm AFN operation with ncam 13.9r1 on my Zgemma h92hse openatv 7.3
Don't know what went wrong. Now working fine. Thanks.
-
Can somebody please confirm whether AFN channels work with latest version 13.9? On Octagon sf8008 with Openatv-7.4, AFN works fine with oscam-emu 11725 but not with V13.9.
-
Image deleted.
-
HI. Have installed Openspa-8.3.002 on Octagon sf8008. When I go to Multiboot Selector I get a blue screen. Crash log is attached. Any ideas please. Thanks.
-
I have Tivusat card 183D which I have not been using lately. Now channels work only for a few seconds. Can somebody please give me a working config? Using oscam-emu-11724. Thamks.
-
First installation was done in Slot 11. Another installation was made in Slot 3. Got blue screen once again. New crashlog attached.
Can you send us a screenshot with all slots, it seems a crash analysing the slots, maybe the system doesn't like some name.
Thank you for your reply.
You are absolutely correct.
One of my installed Images, curiously enough,
is shown as None None None on the Multiboot Seletor.
I have already written about this about 2 weeks ago on this Forum:-
I have also reported this on the relative Forum.
After seeing your reply, I just hid that Image name and Openspa Multiboot
Selector works outright. Thanks for your help.
-
First installation was done in Slot 11. Another installation was made in Slot 3. Got blue screen once again. New crashlog attached.
-
Today I did a new install of Openspa-8.1.003 but when going to Multiboot Selector, got the blue screen again. Crash log is attached.
-
when you click nothing happens
I downloaded and installed the Image and multiboot selector works fine. Maybe you want to download and re-install image.
