Posts by georgeflu

as i remember, it works with openmultiboot...

Quote from pracu_69

Hi all guys ...

I have my Amiko Alien 2 decoder that is booting ..

When I press the Power button while I press it, I do not see the option of selecting ENIGMA or SPARK.

I was connected by null modem cable and I did the procedure I found on the internet but without results.

Is there a procedure to download uboot and try to retrieve it?

This is the procedure I did:

Code

set bootargs console=ttyAS0,115200 rw ramdisk_size=6144 init=/linuxrc root=/dev/ram0 nwhwconf=device:eth0,hwaddr:00:06:37:04:15:00 ip=192.168.40.83:192.168.40.19:192.168.40.1:255.255.255.0.0:lh:eth0ff stmmaceth=msglvl:0,phyaddr:1,watchdog:5000 bigphysarea=6000
nboot.i 0x80000000 0 0x00100000 ;bootm 0x80000000 

This is see Help me..... Tks

Display More

you are not writting the way that you are trying to change from spark to enigma2, so just to remind... power off the receiver, push and keep "ok" button,power on the receiver,wait 5 sec. "up" button for selecting spark,"down" button for selecting enigma.than press once "right" button to boot...

you can take a look in first minutes of this video

you need oscam emu for arm, you can find bin here Latest OSCam For ARM Based Receivers

you have to install/modify config and scripts for your image.

also master G posted it in message #5#

you also need to know,that your receiver can decrypt powervu,only using stream relay function.

no,it not works in 644. just tried (the strange is,that is not stop if i change cam,except if i will shut it down from ncam webif or telnet)

scripts need 755 attributes,because they are executable files...

i just tried and it works...

i remind that both files need 755 attributes,as they are executable...

Quote

FTP to /etc/init.d

Send attached softcam.ncam to this folder.

Change permissions on softcam.ncam to 644.

as i remember the script file also need 755 attributes...

and may this post help you

csat pls help

ah in the top of the page,there is a window "oscam" . you can select the "oscam config generator" and you can do the one for your package...

:?::?::?:

ok,now it is easier for someone to help you. but still not quite clear. there isn't a config which contains everything...,you need config for something...

personaly i do not know the config for csat card (you own a card right?) but you still have to refer what card do you have (and as i saw,in this version only via is supported) etc...

for what,what is the reason?

i will start from the bottom. does not matter if your tv is 43 inches,or 60 inches. the resolution is both 4K, so a 4K receiver will do the same job in both tv. you can select one by other criteria

now,about the resolution. personaly i use the "autoresolution" plugin,and i let the natural resolution of the channel to go in the tv. otherwise,by setting a very high standar video resolution (for example 1080p 60fps) you may destroy some channels because of their low resolution (the receivers scaler will strech them...) and as i know there isn't even a 1080p channel in any satellite (4k channels are not for this receiver)

here Joeuser's Taapat based image with new hardware DES drivers. (powervu...) you can download a build to handle pids (for the moment it not works cccam). download it (decompress it) and put the bin in var/emu directory. change attributes to 755 and than you can start it from alternative cam manager.

about config... you do not need something special. or from your browser,open thi receivers ip:8888 (or 8088 i do not remeber) and set your config from oscam webif.