Posts by Nudel

Hi.

I didn't wanted to do a new thread about this.

My box has the two LAN lights. But will not start.
So I hope someone will give me a push in the right direction.

I have measured the 8pins.
And got the following result;

Pin 1 - 1.22V With power - 638ohm - Without power - 60
Pin 2 - 2.60V With power - 822ohm - Without power - 82
Pin 3 - 3.30V With power - 838ohm - Without power - 104
Pin 4 - 3.31V With power - 829ohm - Without power - 450
Pin 5 - 5.01V With power - 946ohm - Without power - 101
Pin 6 - 12.28V

The two points above the USB port;
Pin 1 - Gnd?
Pin 2 - 0V 130 Ohm.

I have also measured the U23, U24, U25 chips.
And got the following result;

U23
Pin 1 - 1.25V
Pin 2 - 1.25V
Pin 3 - 1.25V
Pin 4 - 1.85V
Pin 5 - 12.27V
Pin 6 - 12.27V
Pin 7 - 12.27V
Pin 8 - 12.27V

U25
Pin 1 - 0V
Pin 2 - 0V
Pin 3 - 0V
Pin 4 - 4.18V
Pin 5 - 1.2V
Pin 6 - 1.2V
Pin 7 - 1.2V
Pin 8 - 1.2V

U24
Pin 1 - 6.2V
Pin 2 - 4.2V
Pin 3 - 0V
Pin 4 - 0V
Pin 5 - 4.98V
Pin 6 - 0V
Pin 7 - 1.2V
Pin 8 - 1.25V
Pin 9 - 3.13V
Pin 10 - 0.66V
Pin 11 - 1.3V
Pin 12 - 4.48V
Pin 13 - 0V
Pin 14 - 1.85V

Also measured the U22
Pin 1 - 12.27V
Pin 2 - 0V
Pin 3 - 0V
Pin 4 - 0V
Pin 5 - 0V
Pin 6 - 0V
Pin 7 - 0.08V

Does this make any sense?

I dont get the "NO CA ERROR"
The problem I have is that the box dont start at all.

When I connect the power cord, nothing happens.
The screen just flicker for 1sec.

I searched a little on 8a8f8-forum. And found some good info.
I found this picture;

http://www.8a8f8.com/ubbthreads.php/ubb/download/Number/10924/filename/dm800hd-Fault-finder-pinout-2013.jpg

I have the readings on pin 1-8
But I dont have the 5V on the pins in the upper right.

The question is why...

The new PSu arrived today.
But no difference.

The screen shows something for 1second.
But then shuts of.

The weird thing is that I have managed to start it 2times.
But when restarted - it is the same.

A user on a Swedish Forum told me that SSL 84D have a tendency to "destroy" boxes.

Is there any truth in what he said?

Thanks for answer.

The PSU that came with the box was 3amp.
But when its connected I hear a very high pitch tone from it.

I tried another psu that I had for a ext hdd.
Its 2.0 amp. But nothing happens.

No int hdd connected. And I have removed thé tuner.
But nothing.

Hi.

That does not help.
I have waited several hours.

The only thing that happens is that the screen flickers for 1sek.

Then completely black.

So no "no ca error"
If it would have been that I would have fixed it easyly

- - - Updated - - -

I actually got i started right now.
I managed to get ssl 84A installed.
But after that it had to reeboot.

And now it is the same.
The screen is pitch black. And i can not connect to it.

I got a bit confused now.

I found an old PSU.
So I tried it out.
The box booted up.
I missed pressing the button to come to the DHCP meny.
But it booted all the way.

But when i turned it off, I cant get it going again.

And dont tell me to put in and out the cable fast, cause i have done that like 10k times.

I will download and try.
Thanks for the tip.

Should i buy one even when the LAN-lights lit with the one I have now?

- - - Updated - - -

Well, I ordered one now anyway.
Will see if that will get it going.

Hi.

Thanks for quick answer.

Unfortunantly the box dont start. So I cant connect to it via LAN.

When i insert power cable absolutely nothing happens.

- - - Updated - - -

I think I have tried it all now.
Nothing seems to work.

The box doesn't start.
So not any program can connect to it..

How the hell do i solve this?

Hi.

I recently bought a 800HD PVR.
I could connect to it via FTP.
But I wanted to upgrade it.

So I searched for a few hours and found a recommended bootloader
I flashed it via HTTP with no problems.
But when I started it up later, I had the NO CA error.
Well, no problems there. But i learned that I had bought a clone...

I then searched some more and found that this setup would work;
sim201_ssl84a
OpenPli-3.0-hdglass16-8.55-DM800-SIM2-SSL84D-26.10.2014-Houara

So I connected the box with both the rs232 and LAN cable.
No problems there eather.
Box connected. Said it was a DM800 down the corner in Dreamup.

I then flashed the bootloader.
And I also flashed the PLI image through Dreamup.

But after 99% of installation I got a error message.
"Error - box will be useless now"

Didnt thought much more of that. But I discoennected the box.
And now it is impossible to connect to it.
I have tried every single program to connect to it, but nothing.

When i put in the power cable the ethernet connector lights up.
But it is impossible to start it.

I have disconnected the tuner.
I have removed the SIM.

How do I fix this box?

SIM 2.01