Display Moreuse newcamd
in config
[newcamd]
port = 2153@1810:000000;2154@1803:000000
key = 0102030405060708091011121314
keepalive = 1
change caid to what you want to use
and
user
[account]
user = user
pwd = pass
caid = 1810
group = 1
cccreshare = 2
in cccam
N: oscam ip 2153 user pass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 256
then use cccam to distrubute to others
can you read ?
cos i dont think you have read anything
answer this
what do you want to watch in a room with 1 device
that will use CCcam
what sat is it pointed at
you cant have all 3 of them motorised
http://www.streamboard.tv/oscam/wiki/CardsList
caid and providers
if that old device is using CCcam it will accept N lines
how many devices are you using ?
do not use hostname inside your network ie home
it not a good idea
allways use ip of box or linux server
and never use the same port twice withen that network
i would also never use same user pass withen that too
use newcamd
in config
[newcamd]
port = 2153@1810:000000;2154@1803:000000
key = 0102030405060708091011121314
keepalive = 1
change caid to what you want to use
and
user
[account]
user = user
pwd = pass
caid = 1810
group = 1
cccreshare = 2
in cccam
N: oscam ip 2153 user pass 01 02 03 04 05 06 07 08 09 10 11 12 13 14 256
then use cccam to distrubute to others
change this
[account]
user = 91816554
pwd = 488115
monlevel = 4
group = 1,2
allowedprotocols = cccam
cccmaxhops = 4
keepalive = 1
to this
[account]
user = 91816554
pwd = 488115
group = 1,2
Oscam server with CCCcam client not working
If you have no card
i wouldn't do what your doing
your going to be blacklisted for double/treble logging
and if you persist with it
use newcamd
Ok, as i can see it isnt a way to pass multiple caid in a single port.
Is there any other protocol to connect 2 oscams without any limits as oscam has with newcamd because i cannot create more than 32 ports
as you mever stated how many caids in first post and now you say more than 32
how can you have an answer ?
the 1st answer pass multiple caid
anyway camd35 ie cs357x
[newcamd]
port = port1@caid:prvid; port2@caid:prvid; port3@caid:prvid
key = 0102030405060708091011121314
keepalive = 1
mgclient = 1
Display MoreAutomated MultiCS r84 Install -Debian or Ubuntu 16.xx 18.04 x32/x64
MultiCS is already a very simple & user friendly install but here is a quick script to automate the x32/x64 selection, Install MultiCS & setup MultiCS to start on boot
Tested & Working on:
WattOS R10 amd64 & x32
Ubuntu Server 16.xx amd64 & x32
Ubuntu Server 18.04 amd.64Debian 10 amd.64
(I am not sure it would work on older releases as it uses systemd )
Extract the contents of MultiCS Install.rar
ftp multics.r84 folder & multics_Install.sh to /tmp folder on your server
Log into your server as root user with putty or similar ssh client
chmod the Script with this commandCodechmod 755 /tmp/multics_Install.sh
Run the Script with these commands
Codecd /tmp ./multics_Install.sh
When the script finished you will have MultiCS Installed & Running
You can check your MultiCS Webif page by typing your server ip & MultiCS webif port no. (192.168.*.*:5500) in the address bar of your browser.
Username: admin
Password: admin
NOTE: This script only installs MultiCS with dummy servers, profiles etc etc.. You will have to configure it yourself
for some of the latest distro's
to add to above post
NOTE: this version of multics will not let you start with invalid PROFILES!
Hellboy version's of Multics you have to correct your PROFILES to able to run.
IE
0100 (seca) as PROVID should not contain 000000
0500 (via) as PROVID should not contain 000000
0DXX (cryptoworks) as PROVID should not contain 000000
18XX (nagra) as PROVID should have only 000000 ,
EXCEPTION all tunneled Nagra cards like ( 1811,1863,1883 etc. )
0BXX (conax) as PROVID should have only 000000
09XX (nds) as PROVID should have only 000000
06XX (irdeto) as PROVID should have only 000000
4AXX (bulcrypt) as PROVID should have only 000000
NOTE: this version of multics will not let you start with invalid PROFILES!
First time users should start it manually with putty and check the output if there are ERROR Message(s).
All first users should correct their PROFILES before put it in your start scripts,
the ERROR Message will contains the PROFILE name and the ERROR what should be corrected.
and the most stable client emulator
is wicardd
with either of these reader's
mgcamd
[reader]
active = 1
name = dellboy
type = newcamd525
account=user:pass@ip of hellboy:port:0102030405060708091011121314
force_crypted_cw = 1
debug = 0
reconnect_delay = 10
emm_cache = 1
ecm_ttl = 5000
newcamd multi-port
[reader]
active = 0
name = dellboy-
type = newcamd525
account =user:pass@ip of hellboy
multiport = 5201,5202,5203,5204,5205,5206,5207,5208,5209,5210
force_crypted_cw = 1
debug = 1
reconnect_delay = 10
emm_cache = 1
ecm_ttl = 5000
in red important
não posso ver nenhum também
Hi Technodvl2 , I have a HD51 > (openpli) and Dreambox 920 (openvision 9.1) ARM
i don't know or use any of you receivers
i use VU+Zero4k and a dm800se which uses ( mipsel hb-v32 )
both running OpenATV
please read the
important read me file
use at you're own risk
for openpli based ARM receivers ie OpenATV , SatDreamGR
sample of the best multics config by http://www.multics.it
included bin file
multics hellboy v32 Arm
save any config file as you may need it later
save before use you have been warned
start here
then
read all the thread
and i mean all the thread every single entry
can you see SIS ?
if you can than add the rtvi key
P 0056005F 00 62330668A3012C ;RTVi, 4.8E, 12418
P 0056005F 01 1B665F567CDA81 ;RTVi, 4.8E, 12418
Hi, Howto use it whit a sat receiver ?
there are hundreds of sat receiver's ?
